5inch DSI LCD (C)

5inch DSI LCD (C) 5inch Capacitive Touch Screen LCD Raspberry Pi, DSI Interface

{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

{{{name6}}}

Primary Attribute Category: OLEDs / LCDs, LCD, Raspberry Pi LCD {{{userDefinedInfo}}}: {{{userdefinedvalue}}} Brand: Waveshare

Website International: 5inch DSI LCD(B) Chinese: 5inch DSI LCD(B)

Onboard Interfaces DSI

Related Products 15.6inch HDMI LCD (H) (with case) 15.6inch HDMI LCD (H) 15.6inch FHD Monitor 13.3inch HDMI LCD (H) (with case) V2 13.3inch HDMI LCD (H) (with case) 13.3inch HDMI LCD (H) 13.3inch Magic Mirror 13.3inch Magic Mirror C4 13.3inch PiPad 13.3inch PiPad C4 12.5inch FHD Monitor 11.6inch HDMI LCD (H) (with case) 11.6inch HDMI LCD (H) 11.9inch HDMI LCD 10.5inch HDMI AMOLED 10.1inch HDMI LCD 10.1inch HDMI LCD (B) (with case) 10.1inch HDMI LCD (E) 10.1inch HDMI LCD (G) (with case) 10.1inch HDMI LCD (H) (with case) 10.1HP-CAPQLED 9inch 2560x1600 Monitor 9HP-CAPQLED 8.8inch Side Monitor 8inch DSI LCD 8inch DSI LCD (with cam) 7.9inch HDMI LCD 7inch FHD Monitor 7inch HDMI LCD (H) (with case) 7inch HDMI LCD (C) 7inch HDMI LCD (B) 7inch HDMI LCD 7inch DPI LCD 7HP-CAPQLED 7inch DSI LCD 7inch DSI LCD (with cam) 7inch DSI LCD (with case A) 7inch DSI LCD (C) 6inch HDMI AMOLED 5inch HDMI LCD (H) 5inch HDMI LCD (H) V4 5inch HDMI LCD (G) 5inch HDMI LCD (B) 5inch HDMI LCD 5inch HDMI AMOLED 5inch DPI LCD 5inch DSI LCD 5.5inch HDMI AMOLED 4inch HDMI LCD (C) 4inch DSI LCD 4.3inch HDMI LCD (B) 4.3inch DSI LCD 4inch DSI LCD 4inch DPI LCD (B) 4inch DPI LCD (C) 4inch HDMI LCD (H) 4inch HDMI LCD 4inch RPi LCD (C) 4inch RPi LCD (A) 3.5inch DPI LCD 3.5inch HDMI LCD 3.5inch RPi LCD (C) 3.5inch RPi LCD (B) 3.5inch RPi LCD (A) 3.2inch HDMI LCD (H) 3.2inch RPi LCD (B) 2.8inch HDMI LCD (H) 2.8inch DPI LCD 2.8inch RPi LCD (A) 2.23inch OLED HAT 1.3inch OLED HAT 1.3inch LCD HAT 1.44inch LCD HAT 1.8inch LCD Module EINK-DISP-103 LCD1602 RGB Module Pico-Clock-Green Pico-RGB-Matrix-P3-64x32 RGB-Matrix-P3-64x32

Features

• 5inch DSI touch screen, five-point capacitive touch control
• IPS display panel with a hardware resolution of 1024×600
• Toughened glass touch panel, hardness up to 6H
• Support Pi5/CM5/4B/CM4/3B+/3A+/3B/CM3+/CM3
• Directly drive the LCD by the DSI interface on the Raspberry Pi, with up to 60Hz refreshing rate
• Supports Bookworm/Bullseye/Buster systems when working with Raspberry Pi
• Supports software control of backlight brightness

Video Tutorial

Interface Definition

PIN	Label
1	GND
2	DSI1_DN1
3	DSI1_DP1
4	GND
5	DSI1_CN
6	DSI1_CP
7	GND
8	DSI1_DN0
9	DSI1_DP0
10	GND
11	SCL0
12	SDA0
13	GND
14	3V3
15	3V3

Hardware Connection

Working with Pi5/CM5/CM4/CM3+/CM3

Connect the DSI interface of the display to the 22PIN DSI1 interface of the Raspberry Pi board using the "DSI Cable-12cm" cable

The installation effect is as follows:

Working with Pi4B/3B+/3B/3A+

Connect the DSI interface of the display to the DSI interface of the Raspberry Pi board using a 15PIN FPC cable

The installation effect is as follows:

Software Setting

For Trixie/Bookworm Systems

Method 1: Use Raspberry Pi Imager to Flash Latest Official Image

• 1. Connect the TF card to the PC, download and use Raspberry Pi Imager to flash the corresponding system image.

• 2. After the image flashing is completed, open the config.txt file in the root directory of the TF card, add the following code at the end of the config.txt, save and safely eject the TF card.

Note: Since Pi5/CM5/CM4/CM3+/CM3 has two mipi DSI interfaces, please note that the correct DSI interfaces and commands are used, DSI1 is recommended by default.

dtoverlay=vc4-kms-v3d
#DSI1 Use
dtoverlay=vc4-kms-dsi-waveshare-panel,7_0_inchC
#DSI0 Use
#dtoverlay=vc4-kms-dsi-waveshare-panel,7_0_inchC,dsi0

• 3. Insert the TF card into the Raspberry Pi, power on the Raspberry Pi, and wait for a few seconds normally to enter the display. After the system starts, the touch function can be used normally.

Method 2: Flash Pre-installed Image

1. Select your corresponding Raspberry Pi version image, download and unzip it as .img file.
Raspberry Pi 5/4B/CM4 Version Download: 5inch DSI LCD (C)-Pi5 pre-installed image
2. Connect the TF card to the PC, format the TF card with SDFormatter software.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click Write to flash the system image.
4. After the image flashing is completed, connect the TF card to the Raspberry Pi, start the Raspberry Pi, and wait for about 30 seconds for it to be displayed and touched normally.

For Bullseye and Buster Systems

Method 1: Install Driver Manually

1. Download the latest version of the image from the Raspberry Pi official website, download the compressed file to your PC, and extract it as .img file.
2. Connect the TF card to the PC, format the TF card with SDFormatter software.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click Write to flash the system image.
4. After the flashing is completed, connect the TF card to the Raspberry Pi, start the Raspberry Pi, and log in to the terminal of the Raspberry Pi (you can connect the Raspberry Pi to the HDMI display or use ssh to log in remotely).

#Step 1: Download and enter the Waveshare-DSI-LCD driver folder
git clone https://github.com/waveshare/Waveshare-DSI-LCD
cd Waveshare-DSI-LCD
 
#Step 2: Enter uname -a on the terminal to view the kernel version, and cd it to the corresponding file directory
#6.1.21 then run the following command
cd 6.1.21
 
#Step 3: Please determine the bits of the current system you are using. For a 32-bit system, proceed to the 32 directory, and for a 64-bit system, proceed to the 64 directory
cd 32
#cd 64
 
#Step 4: Enter your corresponding model command to install the driver
#7inch DSI LCD(C) 1024×600 Driver:
sudo bash ./WS_xinchDSI_MAIN.sh 70C I2C0
 
#Step 5: Wait for a few seconds, when the driver installation is complete and no error is displayed, restart and load the DSI driver to use it normally
sudo reboot
#Note: The steps above require that the Raspberry Pi can connect to the Internet normally 

5. Wait for the system to restart, and it will be able to display and touch normally.

Method 2: Flash Pre-installed Image

1. Select your corresponding Raspberry Pi version image, download and unzip it as .img file.
Raspberry Pi 4B/CM4 version download: Waveshare DSI LCD - Pi4 pre-installed image
Raspberry 3B/3B+/CM3 Version Download: Waveshare DSI LCD - Pi3 pre-installed image
2. Connect the TF card to the PC, format the TF card with SDFormatter software.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click Write to flash the system image.
4. After the flashing is completed, open the config.txt file in the root directory of the TF card, add the following code under [all], save and safely eject the TF card.

dtoverlay=WS_xinchDSI_Screen,SCREEN_type=2,I2C_bus=10,Backlight=128
dtoverlay=WS_xinchDSI_Touch,I2C_bus=10

5. Connect the TF card to the Raspberry Pi, start the Raspberry Pi, and wait for about 30 seconds before it can be displayed and the touch function can be used normally.

Precautions for Buster System

1. Update the system to execute the following commands

sudo apt-get update
sudo apt-get full-upgrade

Note: After updating the system, some files of the originally installed driver may be overwritten, and you need to reinstall the driver to display it normally.
2. Replace the motherboard
If the driver originally installed on the Raspberry Pi 4 Model B, if the user changes the motherboard, such as changing it to the Raspberry Pi 3 Model B+, the display will not display properly.
Because Pi4 and Pi3 need to load different driver files, you need to reinstall the driver according to Method 1: Install Driver Manually on the new motherboard for it to display normally.

Adjust Backlight Brightness

Graphical Interface Backlight Adjustment

The following steps are based on the Trixie system:

• 1. Click the menu in the upper left corner, then go to "Preferences" → "Control Center", and select "Screens";
  

• 2. Go to "Screen" -> "DSI-2" -> "Brightness", select and adjust the desired backlight brightness, and finally click "Apply" to save the settings.

In the Bookworm system, this setting entry is located at "Screen Configuration" → "Screen".

Use Waveshare Backlight Adjustment Application

You can also use the graphical backlight adjustment tool provided by Waveshare:

wget https://files.waveshare.com/wiki/common/Brightness.zip
unzip Brightness.zip
cd Brightness
sudo chmod +x install.sh
./install.sh

After the installation is completed, you can open the demo in the Start Menu -> Accessories -> Brightness, as shown below:

Adjust Backlight Brightness Using Terminal

echo X | sudo tee /sys/class/backlight/*/brightness

Where X represents any number from 0 to 255. 0 means the darkest backlight, and 255 means the brightest backlight. For example:

echo 100 | sudo tee /sys/class/backlight/*/brightness
echo 0 | sudo tee /sys/class/backlight/*/brightness
echo 255 | sudo tee /sys/class/backlight/*/brightness

Trixie/Bookworm Display Rotation

GUI interface rotation
The following steps are based on the Trixie system:

• 1. Click the menu in the upper left corner, then go to "Preferences" -> "Control Center", and select "Screens";
  

• 2. Go to "Screen" -> "DSI-1" -> "Touchscreen" and check "10-0014 Goodix Capacitive TouchScreen";
  

• 3. Go to "Screen" -> "DSI-2" -> "Orientation", check the direction you need to rotate, and finally click "Apply" to complete the display and touch synchronous rotation.
  

• In the Bookworm system, this setting entry is located at "Screen Configuration" -> "Screen".

Note: The above synchronous rotation method is only supported on Trixie/Bookworm system systems. For the Bullseye/Buster system, the touch rotation needs to be set manually and individually after the rotation is displayed.

Bullseye/Buster Display Rotation

• 1. Open the "Screen Configuration" application;
  

• 2. Go to "Screen" -> "DSI-1" -> "Orientation", check the direction you need to rotate, and finally click "Apply" to complete the display rotation.

Bullseye/Buster Touch Rotation

sudo nano /boot/config.txt
# The command to modify the touch rotation angle at the end of the config.txt file will take effect after restarting (the command for 0° touch direction exists by default)
#90°:
dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy,I2C_bus=10
#180°:
dtoverlay=WS_xinchDSI_Touch,invertedx,invertedy,I2C_bus=10
#270°:
dtoverlay=WS_xinchDSI_Touch,invertedy,swappedxy,I2C_bus=10
#0°:
dtoverlay=WS_xinchDSI_Touch,I2C_bus=10

lite Version Display Rotation

sudo nano /boot/cmdline.txt
#Add a command to display the rotation angle at the beginning of the cmdline.txt file, and save it to take effect after restarting
#Display rotation 90 degrees
video=DSI-1:1024x600M@60,rotate=90
#Display rotation 180 degrees
video=DSI-1:1024x600M@60,rotate=180
#Display rotation 270 degrees
video=DSI-1:1024x600M@60,rotate=270

Set Screen Off and On

Run the following command on the Raspberry Pi terminal and the screen will be turned off:

wlr-randr --output DSI-2 --off
# DSI-2 needs to be modified to the actual display in use, e.g. "DSI-1" or "HDMI-A-1"

Run the following command on the Raspberry Pi terminal and the screen will be turned on:

wlr-randr --output DSI-2 --on
# DSI-2 needs to be modified to the actual display in use, e.g. "DSI-1" or "HDMI-A-1"

Note: This command is only applicable to the Labwc and Wayfire graphical interfaces and not to the X11 graphical interface.

Screen Sleep

Run the following command on the Raspberry Pi terminal and the screen will enter sleep mode:

xset dpms force off

Note: This command is only applicable to the X11 graphical interface and not to the Labwc and Wayfire graphical interfaces.

Disable Touch

At the end of the config.txt file, add the following command corresponding to disabling touch (the config file is located in the root directory of the TF card, which can also be accessed via the command: sudo nano /boot/config.txt):

disable_touchscreen=1

Note: After adding a command, it needs to be restarted to take effect.

Resources

• 5inch DSI LCD 3D diagram
• 5inch DSI LCD (D) 2D diagram

FAQ

Question: Why is there no backlight on the screen when starting the system for the first time?

 Answer:

① Press the following button to increase the screen backlight brightness;

② Run the following command to set the system software brightness;

echo 128 | sudo tee /sys/class/backlight/*/brightness

Support

Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)

Submit Now