Binocular Camera Base Board Designed for Raspberry Pi Compute Module 4, Optional Interface Expander

SKU: 21160
Part Number: CM4-DUAL-CAMERA-BASE-Acce-A
Brand: Waveshare

$75.99
$75.192+
$74.793+
$74.634+
Description

Details

Binocular camera base board Designed for Raspberry Pi Compute Module 4, optional interface expander
Binocular camera base for CM4

suitable for evaluating the Raspberry Pi CM4 or being integrated into end products

Designed for Compute Module 4 Lite/eMMC variants

Ordering options

Dual camera base only
Standard CM4 socket, dual cameras onboard, supports video output for all CM4 variants, along with networking and USB connectivities.

Dual camera base + Interface expander
Comes with additional interface expander, providing standard 40PIN GPIO header for HATs, M.2 slot for SSD or communication module, and more video/USB ports.

Please check the Package Content section for exact part list.
Connecting with Compute Module 4

standard CM4 socket, compatible with Compute Module 4 Lite/eMMC variants

for reference ONLY, CM4 is NOT included.
Dual camera base introduction

providing interfaces including ETH, HDMI, Micro SD, USB

Dual camera base specifications
CM4 socket suitable for all variants of Compute Module 4
Networking Gigabit Ethernet RJ45
USB USB 2.0 × 1
FFC connector HDMI & PCIe & USB FFC connector × 1
GPIO FFC connector × 1
Dual camera pixels 8MP
sensor IMX219
resolution 3280 × 2464 (per channel)
CMOS size 1/4 inch
aperture F2.4
focal length 2.6mm
FOV 83/73/50 degree (diagonal/horizontal/vertical)
distortion < 1%
baseline length 60mm
Video HDMI × 1, supports 4K 30fps output
Storage MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
Power input 5V/2.5A
Dimensions 85.0 × 51.5mm
optional Interface expander introduction

providing interfaces including GPIO, HDMI, USB, M.2 M KEY

Interface expander specifications
USB USB 2.0 × 3
FFC connector HDMI & PCIe & USB FFC connector × 1
GPIO FFC connector × 1
Other connector M.2 M KEY × 1, for connecting NVME SSD or communication module
Raspberry Pi 40PIN GPIO header × 1
Video HDMI × 1, supports 4K 30fps output
Dimensions 85.0 × 51.5mm
8MP, clear imaging, effective recognition

dual 8MP cameras, up to 3280 × 2464 resolution per camera

Dual 4K UHD outputs support*

dual HDMI ports, supports dual 4K 30fps outputs

* the interface expander is required for dual 4K outputs.
Reserved space for heatsink
allows attaching heatsink for better heat dissipation
for reference ONLY, CM4 and heatsink are NOT included.
Extensive applications

for AI applications like vision robots, depth vision projects, stereo vision projects...

Intelligent traffic
Detection and recognition for motor vehicles, non-motor vehicles, pedestrians, traffic signs, traffic events...

Intelligent driving
Recognizing and ranging around vehicles and road conditions, recognizing the driver status and providing intelligent assistance.

Math contest
Suitable for teaching competitions like robotic vision, OpenCV, AI IoT projects, Python programming, and so on.

Robotics
Used on industrial robots field, enabling robot functions like target identification, positioning, size measuring, binocular depth mapping, navigation...

What's On Board

the Dual camera base

  1. CM4 socket
    suitable for all variants of Compute Module 4
  2. HDMI connector
    supports 4K 30fps output
  3. USB 2.0 port
    for connecting sorts of USB devices
  4. PWR & USB
    USB-C connector, 5V DC power supply or USB programming port
  5. BOOT selection
    ON: CM4 will be booted from USB-C interface
    OFF: CM4 will be booted from eMMC or Micro SD card
  1. CM4 status indicator
    PWR: Raspberry Pi power indicator
    ACT: Raspberry Pi operating status indicator
  2. RJ45 Gigabit Ethernet
    10/100/1000M compatible
  3. Micro SD card slot
    for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)
  4. GPIO FFC connector
    for expanding 40PIN GPIO
  5. HDMI & PCIe & USB FFC connector
    for expanding HDMI1, PCIe, USB
  6. Dual cameras
    IMX219, 8MP

the Interface expander

  1. USB 2.0 port
    for connecting sorts of USB devices
  2. HDMI1 connector
    supports 4K 30fps output
  3. HDMI & PCIe & USB FFC connector
    for expanding HDMI1, PCIe, USB
  4. GPIO FFC connector
    for expanding 40PIN GPIO
  1. 40PIN GPIO header
    for connecting sorts of Raspberry Pi HATs
  2. M.2 M KEY
    for NVME SSD, or communication module with PCIE M.2 M KEY interface
  3. M.2 indicator
    indicating operating status of the interface
Outline dimensions
Comparing CM4 expansion boards
CM4 Base BoardInterface count and specifications
PoEGigabit
ETH
40PIN
GPIO
PCIeUSB①DSIHDMICSIRTCFan
Header
Power
Input
Features

NANO A
      2.0×1     ×1     5V CM4 sized

NANO B
  ×1   2.0×1 ×1 ×1 ×1     5V CM4 sized

Duino
      M.2 M 2.0×1   ×1 ×1     5V Arduino compatible

mini Base A
  ×1 M.2 M 2.0×4 ×1 ×2 ×2   5V 5V mini size

mini Base B
  ×1 M.2 M 2.0×4 ×1 ×2 ×2 5V 5V mini size

Touch screen
  ×1   M.2 M 2.0×4   ×1 ×1     5V IPS screen

Mini Dual Gigabit
  ×2   2.0×1         5V SH1.0 5V dual ETH

Binocular camera
  ×1 M.2 M 2.0×4   ×2       5V dual 8MP
cameras

4CH RS485
  ×1     2.0×2   ×1 ×2 ×1 5V 7-36V dual ETH

Dual Gigabit ETH
  ×2   3.0×3 ×1 ×2 ×2 5/12V 7-36V  

IoT Dual Gigabit ETH
  ×2   3.0×2 ×1 ×2 ×2 5/12V 5V 5G/4G support

IoT Base
×1   Gen2×1 2.0×2 ×2 ×2 ×2 5/12V 7-36V 5G/4G support
RS232
RS485
ADC

PoE Base (B)
×1 Gen2×1 2.0×4 ×2 ×2 ×2 5/12V 5V RS232
RS485

PoE UPS Base
×1 M.2 M 2.0×4 ×1 ×2 ×2 5/12V 7-36V UPS

PoE Base
×1   3.0×4 ×2 ×2 ×2 5/12V 7-36V  

Raspberry Pi official
×1 Gen2×1 2.0×4 ×2 ×2 ×2 12V 12V  

Wireless base
  ×1   M.2 B /
Mini-PCIe
2.0×3   ×1 ×1 5/12V 5V or
7-36V
5G/4G support
RS485
CAN
rail-mount

5″ touch screen
×1 M.2 M 2.0×4   ×1 ×2 5/12V 5V  

7″ all-in-one
  ×1   M.2 M 2.0×4 used ×1 used 5/12V
used
7-36V touch screen
camera
speaker
Note ① USB 3.0 is equivalent to USB 3.2 Gen1
② There's PoE header only on the Raspberry Pi official IO board without PoE circuit, that means additional PoE module is required for the official IO board to enable PoE feature.
Unless otherwise specified, the PoE feature here stands for integrating 802.3af-compliant PoE circuit (5V/2.5A).
Resources & Services

* Resources for different product may vary, please check the wiki page to confirm the actually provided resources.

Weight: 0.072 kg

Quick Overview

  1. Dual camera base x1
  2. Screws pack x1
  3. OPTIONS Interface expander x1
  4. OPTIONS FFC 2PCS x1
1
2
3
4