Difference between revisions of "DoWatch DIY06"
(Created page with "File:DoWatch_63.jpg <br><font color="#008DE6">Place the spring bars into the watch strap.</font> <br> File:DoWatch_64.jpg <br><font color="#008DE6">Remove the impuriti...") |
|||
Line 1: | Line 1: | ||
− | [[File: | + | [[File:DoWatch_DIY06-1.jpg]] |
<br><font color="#008DE6">Place the spring bars into the watch strap.</font> <br> | <br><font color="#008DE6">Place the spring bars into the watch strap.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-2.jpg]] |
<br><font color="#008DE6">Remove the impurities in the lugs holes for installing the spring bars.</font> <br> | <br><font color="#008DE6">Remove the impurities in the lugs holes for installing the spring bars.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-3.jpg]] |
<br><font color="#008DE6">Put the one end of the spring bar into the lugs hole.</font> <br> | <br><font color="#008DE6">Put the one end of the spring bar into the lugs hole.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-4.jpg]] |
<br><font color="#008DE6">Then, put the other end into another lugs hole.</font> <br> | <br><font color="#008DE6">Then, put the other end into another lugs hole.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-5.jpg]] |
<br><font color="#008DE6">Install the other watch strap with the same method presented above.</font> <br> | <br><font color="#008DE6">Install the other watch strap with the same method presented above.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-6.jpg]] |
<br><font color="#008DE6">Press the down key (Menu key), the OLED will show the time information.</font> <br> | <br><font color="#008DE6">Press the down key (Menu key), the OLED will show the time information.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-7.jpg]] |
<br><font color="#008DE6">Press the down key again to enter the information interface, and check whether the temperature information is correct.</font> <br> | <br><font color="#008DE6">Press the down key again to enter the information interface, and check whether the temperature information is correct.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-8.jpg]] |
<br><font color="#008DE6">Initialize the RTC IC</font> <br> | <br><font color="#008DE6">Initialize the RTC IC</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-9.jpg]] |
<br><font color="#008DE6">In case of low battery or custom program error, you can short break the contacts + and - on the back shell of the DoWatch to reset the MCU.</font> <br> | <br><font color="#008DE6">In case of low battery or custom program error, you can short break the contacts + and - on the back shell of the DoWatch to reset the MCU.</font> <br> | ||
<font color="#fd0d3a">The operation of short-breaking should not exceed 0.5 sec, to avert damage from overcharging. It is recommended to reset the MCU by ISP.</font> <br> | <font color="#fd0d3a">The operation of short-breaking should not exceed 0.5 sec, to avert damage from overcharging. It is recommended to reset the MCU by ISP.</font> <br> | ||
− | [[File: | + | [[File:DoWatch_DIY06-10.jpg]] |
<br><font color="#008DE6">The contacts + and – can also be used to perform ISP to the MCU. For more details, please refer to Customized Development Guide. </font> <br> | <br><font color="#008DE6">The contacts + and – can also be used to perform ISP to the MCU. For more details, please refer to Customized Development Guide. </font> <br> | ||
Latest revision as of 07:29, 20 March 2015
Place the spring bars into the watch strap.
Remove the impurities in the lugs holes for installing the spring bars.
Put the one end of the spring bar into the lugs hole.
Then, put the other end into another lugs hole.
Install the other watch strap with the same method presented above.
Press the down key (Menu key), the OLED will show the time information.
Press the down key again to enter the information interface, and check whether the temperature information is correct.
Initialize the RTC IC
In case of low battery or custom program error, you can short break the contacts + and - on the back shell of the DoWatch to reset the MCU.
The operation of short-breaking should not exceed 0.5 sec, to avert damage from overcharging. It is recommended to reset the MCU by ISP.
The contacts + and – can also be used to perform ISP to the MCU. For more details, please refer to Customized Development Guide.
- About DoWatch
- DoWatch: Welding OLED and MCU to Board C
- DoWatch: Welding other parts to Board C and testing
- DoWatch: joint the boards A, B and C
- DoWatch: install magnet, steel ball and Lithium battery, and weld the rest components
- DoWatch: install watch strap and perform test
- Charger: Welding and testing