11.9inch DSI LCD
| ||
Overview
Feature
- 11.9-inch IPS display with capacitive touch panel, hardware resolution is 320 x 1480.
- Capacitive touch, supports up to 5-point touch.
- Toughened glass capacitive touch panel, 6H hardness.
- DSI interface, refresh rate up to 60Hz.
- Working with Raspberry Pi, we provide the driver for Raspberry Pi OS.
- Brightness is adjustable by software.
- Support Pi 4B/3B+/3A+, CM3+/4,must be used with adapter cable.
Working with RPi
Hardware Connection
1. Use a 15PIN FPC cable to connect the display DSI interface to the DSI interface of the Raspberry Pi board.
2. The Raspberry Pi is installed on the display board with the back facing down, and the 5V power supply and I2C communication are connected through the 4PIN.
The back lock installation effect is as follows:
Software Debugging
Method 1: Install Manually
1) Download the image from the Raspberry Pi website.
2) Connect the TF card to the PC, and use SDFormatter software to format the TF card.
3) Open the Win32DiskImager software, select the system image downloaded in step 1, and click 'Write' to burn the system image.
4) After the programming is completed, connect the TF card to the Raspberry Pi, start it, and log in to the terminal of the Raspberry Pi. (you can connect the Raspberry Pi to an HDMI display or log in remotely with ssh.)
#Step 1: Download and enter the Waveshare-DSI-LCD driver folder git clone https://github.com/waveshare/Waveshare-DSI-LCD cd Waveshare-DSI-LCD #Step 2: Enter uname -a in the terminal to view the kernel version and cd to the corresponding file directory #6.1.21 then run the following command cd 6.1.21 #Step 3: Please check the bits of your system, enter the 32 directory for 32-bit systems, and enter the 64 directory for 64-bit systems cd 32 #cd 64 #Step 4: Enter your corresponding model command to install the driver, pay attention to the selection of the I2C DIP switch #11.9inch DSI LCD 320×1480 driver: sudo bash ./WS_xinchDSI_MAIN.sh 119 I2C0 #Step 5: Wait for a few seconds, when the driver installation is complete and no error is prompted, restart and load the DSI driver and it can be used normally sudo reboot
Note: The above steps need to ensure that the Raspberry Pi can be connected to the Internet normally.
5. Wait for the system to restart, it will be able to display and touch normally.
Method 2: Program Pre-install Image
1. Select your corresponding Raspberry Pi version image, download it, and decompress it as a ".img" file.
Raspberry Pi 4B/CM4 version download: Waveshare DSI LCD - Pi4 pre-install image
Raspberry Pi 3B/3B+/CM3 version download: Waveshare DSI LCD - Pi3 pre-install image
2. Connect the TF card to the PC and use SDFormatter to format the TF card.
3. Open Win32DiskImager software, choose the system image prepared in the first step, and then click "write" to write the system image.
4. After the programming is finished, open the config.txt file in the root directory of the TF card, add the following code under [all], save, and eject the TF card safely.
dtoverlay=WS_xinchDSI_Screen,SCREEN_type=6,I2C_bus=10 dtoverlay=WS_xinchDSI_Touch,invertedx,invertedy,I2C_bus=10
5. Connect the TF card to the Raspberry Pi, and start the Raspberry Pi, wait for about 30 seconds to display and touch normally.
Rotation
Graphical Interface Rotation
In the start menu, select: Preferences->Screen Configuration->Configure->Screens->DSI-1->Orientation, select the corresponding angle in it, click "√", select Yes, and restart.
Touch To Rotate
sudo nano /boot/config.txt #Modify the instruction of the touch rotation angle at the end of the config.txt file, and it will take effect after restarting (there is a 0° touch direction instruction by default) #90 dtoverlay=WS_xinchDSI_Touch,invertedx,invertedy #180 dtoverlay=WS_xinchDSI_Touch,invertedy,swappedxy #270 #dtoverlay=WS_xinchDSI_Touch #0 #dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy
Backlight Control
Method 1: Graphical Interface Dimming
Using the application provided by Waveshare:
cd Waveshare-DSI-LCD # Determine the currently used kernel version, such as the 5.15.61 kernel, and run the following command cd 5.15.61 #Check the bits of the system, the 32-bit system enters 32 directory, 64-bit system enters 64 directory cd 32 #cd 64 cd Backlight sudo ./install.sh
After the installation is complete, you can open the program in the Start menu - > Accessories - > Brightness, as shown below:
Method 2: Lite Version Dimming Command
To adjust the system command of the lite version, after entering the root privilege, execute the following command on the Raspberry Pi terminal:
echo X > /sys/waveshare/rpi_backlight/brightness
(X value in the range of 0~255)
For example:
sudo su root echo 100 > /sys/waveshare/rpi_backlight/brightness
Disable Touch
At the end of the config.txt file, add the following commands corresponding to disabling touch (the config file is located in the root directory of the TF card, and can also be accessed through the command: sudo nano /boot/config.txt):
disable_touchscreen=1
Note: After adding the command, it needs to be restarted to take effect.
Precaution
1. Update the system, such as executing the following command:
sudo apt-get update sudo apt-get full-upgrade
After updating the system, some files of the originally installed driver may be overwritten, and the driver needs to be reinstalled to display normally.
2. Replace the motherboard
If the driver is originally installed on the Raspberry Pi 4 Model B, the user replaces the motherboard, such as modifying it to a Raspberry Pi 3 Model B+, the display will not display properly.
Because Pi4 and Pi3 need to load different driver files, you need to reinstall the driver on the new motherboard to display properly.
Resource
Software
3D Drawing
Pre-install image
FAQ
{{{5}}}
Support
Technical Support
If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 AM GMT+8 (Monday to Friday)