10.1inch DSI LCD (C)

10.1inch Capacitive Touch Display for Raspberry Pi, 1280×800, IPS, DSI Interface

Features

10.1inch DSI touch screen, ten-point capacitive touch control
IPS display panel with a hardware resolution of 1280×800
Adopt the optical bonding process for clearer picture quality
Toughened glass touch panel, hardness up to 6H
Support Pi5/CM5/4B/CM4/3B+/3A+/3B/CM3+/CM3
Directly drive the LCD by the DSI interface on the Raspberry Pi, with up to 60Hz refresh rate
Supports Bookworm/Bullseye/Buster systems when working with Raspberry Pi
Supports software control of backlight brightness

Video Tutorial

Interface Definition

PIN	Label
1	GND
2	DSI1_DN1
3	DSI1_DP1
4	GND
5	DSI1_CN
6	DSI1_CP
7	GND
8	DSI1_DN0
9	DSI1_DP0
10	GND
11	SCL0
12	SDA0
13	GND
14	3V3
15	3V3

Electrical Specifications

Parameters	Minimum Value	Standard Value	Maximum Value	Unit	Note
Input voltage	4.75	5.00	5.30	V	Note 1
Input current	-	0.88	TBD	A	Note 2
Operating temperature	0	25	60	℃	Note 3
Storage temperature	-10	25	70	℃	Note 3

•Note 1: Input voltages exceeding the maximum or improper operation may cause permanent damage to the device.
•Note 2: The input current must be ≥0.88A; otherwise, it may cause startup failure or display abnormalities. Prolonged operation under abnormal conditions could result in permanent damage to the device.
•Note 3: Please do not store the display panel in a high-temperature and high-humidity environment for a long time. The display panel should operate within its limits, otherwise it may be damaged.

Hardware Connection

Working with Pi5/CM5/CM4/CM3+/CM3

1. Use the DSI-Cable-12cm cable to connect the DSI port of the display to the 22PIN DSI1 port of the Raspberry Pi motherboard.
2. Install the Raspberry Pi with its back facing downwards onto the display board, and connect it to the 5V power supply and I2C communication via the 4PIN header.
The installation is as follows:

Working with Pi4B/3B+/3B/3A+

1. Use the 15PIN FPC cable to connect the DSI interface of display to the DSI interface of the Raspberry Pi board.
2. Install the Raspberry Pi with its back facing downwards onto the display board, and connect it to the 5V power supply and I2C communication via the 4PIN header.
The installation is as follows:

Software Setting

For Trixie and Bookworm Systems

1. Connect the TF card to the PC, download and use Raspberry Pi Imager to flash the corresponding system image.

2. After the image flashing is completed, open the config.txt file in the root directory of the TF card, add the following code at the end of the config.txt, save and safely eject the TF card.

Note: Since Pi5/CM5/CM4/CM3+/CM3 has two mipi DSI interfaces, please note that the correct DSI interfaces and commands are used, DSI1 is recommended by default.

dtoverlay=vc4-kms-v3d
#DSI1 Use
dtoverlay=vc4-kms-dsi-waveshare-panel,10_1_inch
#DSI0 Use
#dtoverlay=vc4-kms-dsi-waveshare-panel,10_1_inch,dsi0

3. Insert the TF card into the Raspberry Pi, power on the Raspberry Pi, and wait for a few seconds normally to enter the display. After the system starts, the touch function can be used normally.

For Bullseye and Buster System

Method 1: Install Driver Manually

1. Download the latest version of the image from the Raspberry Pi official website, download the compressed file to your PC, and extract it as .img file.
2. Connect the TF card to the PC, format the TF card with SDFormatter software.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click Write to flash the system image.
4. After the flashing is completed, connect the TF card to the Raspberry Pi, start the Raspberry Pi, and log in to the terminal of the Raspberry Pi (you can connect the Raspberry Pi to the HDMI display or use ssh to log in remotely).

#Step 1: Download and enter the Waveshare-DSI-LCD driver folder
git clone https://github.com/waveshare/Waveshare-DSI-LCD
cd Waveshare-DSI-LCD
 
#Step 2: Enter uname -a on the terminal to view the kernel version, and cd it to the corresponding file directory
#If the kernel version is 6.1.21, run the following command:
cd 6.1.21
 
#Step 3: Please determine the bits of the current system you are using. For a 32-bit system, proceed to the 32 directory, and for a 64-bit system, proceed to the 64 directory
cd 32
#cd 64
 
#Step 4: Enter your corresponding model command to install the driver, pay attention to the selection of the I2C dip switches
#10.1inch DSI LCD(C) 1280×800 Driver:
sudo bash ./WS_xinchDSI_MAIN.sh 101C I2C0
 
#Step 5: Wait for a few seconds, when the driver installation is complete and no error is displayed, restart and load the DSI driver to use it normally
sudo reboot
#Note: The steps above require that the Raspberry Pi can connect to the Internet normally

5. Wait for the system to restart, and it will be able to display and touch normally.

Method 2: Flash Pre-installed Image

1. Select your corresponding Raspberry Pi version image, download and unzip it as .img file.
Raspberry Pi 4B/CM4 version download: Waveshare DSI LCD - Pi4 pre-installed image
Raspberry Pi 3B/3B+/CM3 Version Download: Waveshare DSI LCD - Pi3 pre-installed image
2. Connect the TF card to the PC, format the TF card with SDFormatter software.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click Write to flash the system image.
4. After the flashing is completed, open the config.txt file in the root directory of the TF card, add the following code under [all], save and safely eject the TF card.

dtoverlay=WS_xinchDSI_Screen,SCREEN_type=8,I2C_bus=10
dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy,I2C_bus=10

5. Connect the TF card to the Raspberry Pi, start the Raspberry Pi, and wait for about 30 seconds before it can be displayed and the touch function can be used normally.

Precautions for Buster System

1. Update the system to execute the following commands

sudo apt-get update
sudo apt-get full-upgrade

Note: After updating the system, some files of the originally installed driver may be overwritten, and you need to reinstall the driver to display it normally.
2. Replace the motherboard
If the driver originally installed on the Raspberry Pi 4 Model B, if the user changes the motherboard, such as changing it to the Raspberry Pi 3 Model B+, the display will not display properly.
Because Pi4 and Pi3 need to load different driver files, you need to reinstall the driver according to Method 1: Install Driver Manually on the new motherboard for it to display normally.

Adjust Backlight Brightness

Graphical Interface Backlight Adjustment

The following steps are based on the Trixie system:

1. Click the menu in the upper left corner, then go to "Preferences" → "Control Center", and select "Screens";

2. Go to "Screen" -> "DSI-2" -> "Brightness", select and adjust the desired backlight brightness, and finally click "Apply" to save the settings.

In the Bookworm system, this setting entry is located at "Screen Configuration" → "Screen".

Use Waveshare Backlight Adjustment Application

You can also use the graphical backlight adjustment tool provided by Waveshare:

wget https://files.waveshare.com/wiki/common/Brightness.zip
unzip Brightness.zip
cd Brightness
sudo chmod +x install.sh
./install.sh

After the installation is completed, you can open the demo in the Start Menu -> Accessories -> Brightness, as shown below:

Adjust Backlight Brightness Using Terminal

echo X | sudo tee /sys/class/backlight/*/brightness

Where X represents any number from 0 to 255. 0 means the darkest backlight, and 255 means the brightest backlight. For example:

echo 100 | sudo tee /sys/class/backlight/*/brightness
echo 0 | sudo tee /sys/class/backlight/*/brightness
echo 255 | sudo tee /sys/class/backlight/*/brightness

Trixie/Bookworm Display Rotation

GUI interface rotation
The following steps are based on the Trixie system:

1. Click the menu in the upper left corner, then go to "Preferences" -> "Control Center", and select "Screens";

2. Go to "Screen" -> "DSI-1" -> "Touchscreen" and check "10-0014 Goodix Capacitive TouchScreen";

3. Go to "Screen" -> "DSI-2" -> "Orientation", check the direction you need to rotate, and finally click "Apply" to complete the display and touch synchronous rotation.

In the Bookworm system, this setting entry is located at "Screen Configuration" -> "Screen".

Note: The above synchronous rotation method is only supported on Trixie/Bookworm system systems. For the Bullseye/Buster system, the touch rotation needs to be set manually and individually after the rotation is displayed.

Bullseye/Buster Display Rotation

1. Open the "Screen Configuration" application;

2. Go to "Screen" -> "DS-1" -> "Orientation", check the direction you need to rotate, and finally click "Apply" to complete the display rotation.

Bullseye/Buster Touch Rotation

sudo nano /boot/config.txt
# The command to modify the touch rotation angle at the end of the config.txt file will take effect after restarting (the command for 0° touch direction exists by default)
#0°:
dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy
#90°:
dtoverlay=WS_xinchDSI_Touch,invertedx,invertedy
#180°:
dtoverlay=WS_xinchDSI_Touch,invertedy,swappedxy
#270°:
dtoverlay=WS_xinchDSI_Touch

lite Version Display Rotation

sudo nano /boot/cmdline.txt
#Add a command to display the rotation angle at the beginning of the cmdline.txt file, and save it to take effect after restarting
#Display rotation 90 degrees
video=DSI-1:1280x800e,rotate=90
#Display rotation 180 degrees
video=DSI-1:1280x800e,rotate=180
#Display rotation 270 degrees
video=DSI-1:1280x800e,rotate=270

Set Screen Off and On

Run the following command on the Raspberry Pi terminal and the screen will be turned off:

wlr-randr --output DSI-2 --off
# DSI-2 needs to be modified to the actual display in use, e.g. "DSI-1" or "HDMI-A-1"

Run the following command on the Raspberry Pi terminal and the screen will be turned on:

wlr-randr --output DSI-2 --on
# DSI-2 needs to be modified to the actual display in use, e.g. "DSI-1" or "HDMI-A-1"

Note: This command is only applicable to the Labwc and Wayfire graphical interfaces and not to the X11 graphical interface.

Screen Sleep

Run the following command on the Raspberry Pi terminal and the screen will enter sleep mode:

xset dpms force off

Note: This command is only applicable to the X11 graphical interface and not to the Labwc and Wayfire graphical interfaces.

Disable Touch

At the end of the config.txt file, add the following command corresponding to disabling touch (the config file is located in the root directory of the TF card, which can also be accessed via the command: sudo nano /boot/config.txt):

disable_touchscreen=1

Note: After adding a command, it needs to be restarted to take effect.

Resources

3D Drawing

10.1inch DSI LCD (C) 3D Drawing

2D Drawing

10.1inch DSI LCD (C) 2D Drawing

Pre-installed Images

FAQ

Question:What's the power consumption of 10.1inch DSI LCD (C)?

Answer:

With a 5V power supply, the operating current of the backlight on is about 520mA, and the operating current of the backlight off is about 150mA.

{{{5}}}

Question:How to replace the logo image of Raspberry Pi Booting?