Difference between revisions of "Template:Service00"
From Waveshare Wiki
(→FAQ) |
(→FAQ) |
||
| Line 29: | Line 29: | ||
{{FAQ|2. How to read pin 1 on the adapter board? | | {{FAQ|2. How to read pin 1 on the adapter board? | | ||
*Pin 1 on the PCB is marked with a white round silk screen or square solder joint, as shown in the figure: <br />[[File:Atmel-ICE-10PIN.jpg|400px]]|||}} | *Pin 1 on the PCB is marked with a white round silk screen or square solder joint, as shown in the figure: <br />[[File:Atmel-ICE-10PIN.jpg|400px]]|||}} | ||
| − | {{FAQ|3 | + | {{FAQ|3. Does Atmel-ICE have any related tutorials under ICC8AVR? | |
| − | |||
| − | |||
*For related instructions, please refer to: [https://{{SERVERNAME}}/w/upload/7/7d/ICCAVR8_Debug_%28JTAG_ICE_mkII_Atmel-ICE%29.pdf ICC8AVR Manual], [https://{{SERVERNAME}}/ forum/thread-210-1-1.html ICC8AVR simulation tutorial]|||}} | *For related instructions, please refer to: [https://{{SERVERNAME}}/w/upload/7/7d/ICCAVR8_Debug_%28JTAG_ICE_mkII_Atmel-ICE%29.pdf ICC8AVR Manual], [https://{{SERVERNAME}}/ forum/thread-210-1-1.html ICC8AVR simulation tutorial]|||}} | ||
| − | {{FAQ| | + | {{FAQ|4. Common interface connection diagram of Atmel-ICE| |
*The corresponding relationship between JTAG and ISP serial numbers of the scattered head is as shown in the figure below, the label 0 on the scattered head corresponds to the serial number 1 on the table<br />[[File:Atmel-ICE-Pins-number.jpg|200px]]|*ISP 6PIN The interface serial number corresponds to<br />[[File:Atmel-ICE-ISP-interface.jpg|400px]]|*ISP 6PIN to ISP 10PIN sending and receiving<br />[[File:Atmel-ICE-ISP6-to- ISP10.jpg|200px]]<br />|Note: The red line is VCC}} | *The corresponding relationship between JTAG and ISP serial numbers of the scattered head is as shown in the figure below, the label 0 on the scattered head corresponds to the serial number 1 on the table<br />[[File:Atmel-ICE-Pins-number.jpg|200px]]|*ISP 6PIN The interface serial number corresponds to<br />[[File:Atmel-ICE-ISP-interface.jpg|400px]]|*ISP 6PIN to ISP 10PIN sending and receiving<br />[[File:Atmel-ICE-ISP6-to- ISP10.jpg|200px]]<br />|Note: The red line is VCC}} | ||
Revision as of 09:30, 12 July 2022
FAQ
Answer:
- Click to view detailed device support list: UC3, /supported.devices.AVR.Mega.html Mega, SAM, /webdoc/atmelstudio/supported.devices.AVR.UC3.html Tiny, Xmega
Answer:
- Pin 1 on the PCB is marked with a white round silk screen or square solder joint, as shown in the figure:
Answer:
- For related instructions, please refer to: ICC8AVR Manual, forum/thread-210-1-1.html ICC8AVR simulation tutorial
Answer:
- The corresponding relationship between JTAG and ISP serial numbers of the scattered head is as shown in the figure below, the label 0 on the scattered head corresponds to the serial number 1 on the table
*ISP 6PIN The interface serial number corresponds to
*ISP 6PIN to ISP 10PIN sending and receiving
Note: The red line is VCC
Support
If you require technical support, please go to the Support page and open a ticket.