Difference between revisions of "Template:Jetson Nano Guides for SPI e-Paper"

From Waveshare Wiki
Jump to: navigation, search
Line 556: Line 556:
 
*Ystart: Y coordination of left-top of picture, default 0;
 
*Ystart: Y coordination of left-top of picture, default 0;
  
===Testing Code===
+
====Testing Code====
 
In the above part, we describe the tree structures of Linux codes, here we talk about the testing code for user.
 
In the above part, we describe the tree structures of Linux codes, here we talk about the testing code for user.
 
Raspberry Pi & Jetson Nano: RaspberryPi_JetsonNano\c\examples. The codes in examples are testing code, you can modify the definition in main.c file for different types of e-paper.
 
Raspberry Pi & Jetson Nano: RaspberryPi_JetsonNano\c\examples. The codes in examples are testing code, you can modify the definition in main.c file for different types of e-paper.

Revision as of 05:52, 17 May 2022

User Guides of Jetson Nano

Hardware connection

Because the 40PIN GPIO of Jetson Nano are compatible with Raspberry Pi's and the Jetson.GPIO libraries are compatible with RPi.GPIO, therefore we use the same connection as Raspberry Pi
To connect the e-Paper, you can following the table below
Jetson Nano Connection
e-Paper Jetson Nano Developer Kit
BCM2835 Board
VCC 3.3V 3.3V
GND GND GND
DIN 10(SPI0_MOSI) 19
CLK 11(SPI0_SCK 23
CS 8(SPI0_CS0) 24
DC 25 22
RST 17 11
BUSY 24 18

Install libraries

Open terminal of Jetson Nano and run the following commands to install corresponding libraries:

sudo apt-get update
sudo apt-get install python3-pip
sudo pip3 install Jetson.GPIO
sudo groupadd -f -r gpio
sudo usermod -a -G gpio your_user_name
  • Install I2C libraries
sudo apt-get install python3-smbus
  • Install PIL libraries
sudo apt-get install python3-pil
sudo apt-get install python3-numpy

Download demo codes

Open the terminal of Jetson Nano and clone demo codes by the following commands:

sudo git clone https://github.com/waveshare/e-Paper

Examples

C

  • Enter the folder of C examples
cd ~/e-Paper/RaspberryPi_JetsonNano/
cd c
  • Modify the main.c file for corresponding e-Paper
sudo nano examples/main.c
For example, if you want to update a 2.7inch e-Paper/2.7inch e-Paper HAT, you should modify the main.c file, uncomment the line EPD_2in7_test(), comment others, and save.
E-paper rpi change main.png
  • Compile codes
sudo make clean
sudo make JETSON
  • Try to run the example
sudo ./epd

Support Type

1.02inch(128×80):

EPD_1in02d_test():Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch(1.54inch e-paper c:152×152,others:200×200):

EPD_1in54_test(): Example for 1.54inch e-paper V1(Balck/White): This version is stopped production which can be bought before 2019-11-22;
EPD_1in54_V2_test(): Example for 1.54inch e-paper V2(Balck/White): This is the current version that can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
EPD_1in54b_test(): Example for 1.54inch e-paper B(Black/White/Red);
EPD_1in54b_V2_test(): Example for 1.54inch e-Paper B V2 (Black/White/Red);
EPD_1in54c_test(): Example for 1.54inch e-paper C(Black/White/Red);

2.7inch(264×176):

EPD_2in7_test(): Example for 2.7inch e-paper(Black/White);
EPD_2in7b_test(): Example for 2.7inch e-paper B(Black.White/Red);
EPD_2in7b_V2_test(): Example for 2.7inch e-paper B V2(Black.White/Red);

2.9inch(296×128):

EPD_2in9_test(): Example for 2.9inch e-paper(Black/White);
EPD_2in9_V2_test(): Example for 2.9inch e-paper V2(Black/White);
EPD_2in9bc_test(): Example for 2.9inch e-paper B(Balck/White/Red) and 2.9inch e-paper C(Black/White/Yellow);
EPD_2in9b_V3_test(): Example for 2.9inch e-paper B V3 (Balck/White/Red);
EPD_2in9d_test(): Example for 2.9inch e-paper D(Black/White);

2.13inch(2.13inch e-Paper:250×122,others:212×104):

EPD_2in13_test(): Example for 2.13inch e-paper V1(Black/White), this version is stopped production and it can be bought before 019-05-15;
EPD_2in13_V2_test(): Example for 2.13inch e-paper V2(Black/White) This is the current version with sticker V2 on the backside (2020-07-29);
EPD_2in13_V3_test(): Example for 2.13inch e-paper V3(Black/White) This is the current version with sticker V3 on the backside (2020-07-29);
EPD_2in13bc_test():Example for 2.13inch e-paper B(Black/White/Red)and 2.13inch e-paper C(Blackj/White/Yellow);
EPD_2in13b_V3_test():Example for 2.13inch e-paper B V3(Black/White/Red)
EPD_2in13d_test(): Example for 2.13inch e-paper D(Black/White);

2.66inch (152 x 296)

EPD_2in66_test(): Example for 2.66inch e-Paper (Black/White);
EPD_2in66b_test(): Example for 2.66inch e-Paper B (Black/White/Red);

3.7inch (280 x 480)

EPD_3in7_test(): Example for 3.7inch e-Paper(Black/White);

4.01inch (640x400)

EPD_4in01_test(): Example for the 4.01inch e-Paper HAT (F);

4.2inch(400×300)

EPD_4in2_test(): Example for 4.2inch e-paper(Black/White);
EPD_4in2bc_test(): Example for 4.2inch e-paper B(Black/White/Red);
EPD_4in2b_V2_test(): Example for 4.2inch e-paper B V2(Black/White/Red);

5.65inch (600x448)

EPD_5in65f_test(): Example for for 5.65inch e-Paper F (Seven-color);

5.83inch(600×448):

EPD_5in83_test(): Example for 5.83inch e-paper(Black/White);
EPD_5in83_V2_test(): Example for 5.83inch e-paper V2(Black/White);
EPD_5in83bc_test(): Example for 5.83inch e-paper B(Black/White/Red)and 5.83inch e-paper C(Black/White/Yellow);
EPD_5in83b_V2_test(): Example for 5.83inch e-paper B V2(Black/White/Red)

7.5inch(V1:640×384, V2:800×480):

EPD_7in5_test(): Example for 7.5inch e-paper(Black/White), this version is stopped production and it can be bought before 2019-12-07;
EPD_7in5bc_test(): Example for 7.5inch e-paper B(Black/White/Red)and 7.5inch e-paper C(Black/White/Yellow),7.5inch e-paper B V1 version is stop production and it can be bought before 2019-12-07;
EPD_7in5_V2_test(): Example for 7.5inch e-paper V2(Black/White), This is the current version with V2 sticker on the backside (2020-07-29)
EPD_7in5bc_V2_test():Example for 7.5inch e-paper B V2(Black/White/Red); This is the current version with V2 sticker on the backside. (2020-07-29);

7.5inch(HD880 x 528)

EPD_7in5_HD_test(): Example for 7.5inch e-Paper HD (Black/White);
EPD_7in5b_HD_test(): Example for 7.5inch e-Paper B HD (Black/White/Red);

Python

  • Enter the folder of python code
cd ~/e-Paper/RaspberryPi_JetsonNano/
cd python/examples
  • Check the folder, you can see that there are .py files for different e-Paper.
ls -al
E-paper rpi change python1.png
  • Run the responding example, for example.
sudo python epd_xxx_test.py
sudo python3 epd_xxx_test.py

Support Types

1.02inch(128×80):

epd_1in02_test.py:Example for 1.02inch e-Paper/1.02inch e-Paper Module

1.54inch(1.54inch e-paper c:152×152,others:200×200):

epd_1in54_test.py: Example for 1.54inch e-paper V1(Balck/White): This version is stopped production which can be bought before 2019-11-22;
epd_1in54_V2_test.py: Example for 1.54inch e-paper V2(Balck/White): This is the current version which can be bought now (2020-07-29). The e-Paper has V2 sticker on the backside.
epd_1in54b_test.py: Example for 1.54inch e-paper B(Black/White/Red);
epd_1in54b_V2_test.py: Example for 1.54inch e-paper B V2(Black/White/Red);
epd_1in54c_test.py: Example for 1.54inch e-paper C(Black/White/Red);br />

2.7inch(264×176):

epd_2in7_test.py: Example for 2.7inch e-paper(Black/White);
epd_2in7b_test.py: Example for 2.7inch e-paper B(Black.White/Red);
epd_2in7b_V2_test.py: Example for 2.7inch e-paper B V2(Black.White/Red);

2.9inch(296×128):

epd_2in9_test.py: Example for 2.9inch e-paper(Black/White);
epd_2in9_V2_test.py: Example for 2.9inch e-paper V2(Black/White);
epd_2in9bc_test.py: Example for 2.9inch e-paper B(Balck/White/Red) and 2.9inch e-paper C(Black/White/Yellow);
epd_2in9b_V3_test.py: Example for 2.9inch e-paper B V3(Balck/White/Red;
epd_2in9d_test.py: Example for 2.9inch e-paper D(Black/White);

2.13inch(2.13inch e-Paper:250×122,others:212×104):

epd_2in13_test.py: Example for 2.13inch e-paper V1(Black/White), this version is stopped production and it can be bought before 019-05-15;
epd_2in13_V2_test.py: Example for 2.13inch e-paper V2(Black/White) This is the current version with sticker V2 on the backside (2020-07-29);
epd_2in13bc_test.py: Example for 2.13inch e-paper B(Black/White/Red)and 2.13inch e-paper C(Black/White/Yellow);
epd_2in13b_V3_test.py: Example for 2.13inch e-paper B V3(Black/White/Red)
epd_2in13d_test.py: Example for 2.13inch e-paper D(Black/White);

2.66inch (152 x 296)

epd_2in66_test.py: Example for 2.66inch e-Paper (Black/White);
epd_2in66b_test.py: Example for 2.66inch e-Paoer (Black/White/Red);

3.7inch (280 x 480)

epd_3in7_test.py: Example for 3.7inch e-Paper (Black/White);

4.01inch (640x400)

epd_4in01f_test.py: Example for 4.01inch e-Paper (Seven-color);

4.2inch(400×300)

epd_4in2_test.py: Example for 4.2inch e-paper(Black/White);
epd_4in2bc_test.py: Example for 4.2inch e-paper B(Black/White/Red);
epd_4in2b_V2_test.py: Example for 4.2inch e-paper B V2(Black/White/Red);

5.65inch (600x448)

epd_5in65f_test.py: Example for 5.65inch e-Paper F (Seven-color);

5.83inch(600×448):

epd_5in83_test.py: Example for 5.83inch e-paper(Black/White);
epd_5in83_V2_test.py: Example for 5.83inch e-paper V2(Black/White);
epd_5in83bc_test.py: Example for 5.83inch e-paper B(Black/White/Red)and 5.83inch e-paper C(Black/White/Yellow);
epd_5in83b_V2_test.py: Example for 5.83inch e-paper B V2(Black/White/Red)

7.5inch(V1:640×384, V2:800×480):

epd_7in5_test.py: Example for 7.5inch e-paper(Black/White), this version is stopped production and it can be bought before 2019-12-07;
epd_7in5_V2_test.py: Example for 7.5inch e-paper V2(Black/White), This is the current version with V2 sticker on the backside (2020-07-29)
epd_7in5bc_test.py: Example for 7.5inch e-paper B(Black/White/Red)and 7.5inch e-paper C(Black/White/Yellow),7.5inch e-paper B V1 version is stopped production and it can be bought before 2019-12-07;
epd_7in5b_V2_test.py: Example for 7.5inch e-paper B V2(Black/White/Red); This is the current version with V2 sticker on the backside. (2020-07-29);

7.5inch (HD 880 x 528)

epd_7in5_HD_test.py: Example for 7.5inch e-Paper HD (Black/White);
epd_7in5b_HD_test.py: Example for 7.5inch e-Paper B HD (Black/White/Red);

Description of codes (API)

The libraries for Raspberry Pi and Jetson Nano are the same. Examples contain three parts, hardware interface, EPD driver, and the GUI functions.

C

Hardware interface

Two libraries are used by C example, WiringPi, and BCM2835. The codes use wiringPi by default, if you want to use BCM2835, you can modify the RaspberryPi&JetsonNano\c\Makefile file, modify lines 13 and 14. Change it as below:
E-paper Driver HAT RPI Makefile.png
  • Data type
#define UBYTE   uint8_t
#define UWORD   uint16_t
#define UDOUBLE uint32_t
  • Init and Exit
void DEV_Module_Init(void);
void DEV_Module_Exit(void);
Note: The Init() and Exit() function are used to configure GPIOs . EPD enter sleep mode after Exit() function is used, and the consumption of e-Paper should be 0 in sleep mode if the PCB is Rev2.1 version.
  • GPIO Read/Write
void DEV_Digital_Write(UWORD Pin, UBYTE Value);
UBYTE DEV_Digital_Read(UWORD Pin);
  • SPI transmit data
void DEV_SPI_WriteByte(UBYTE Value);
EPD driver
The driver file are saved under RaspberryPi&JetsonNano\c\lib\e-Paper
E-paper Driver HAT RPI epd.png
  • Initial EPD
For 1.54inch e-Paper, 1.54inch e-Paper V2, 2.13inch e-Paper, 2.13inch e-Paper V2, 2.13inch e-Paper (D), 2.9inch e-Paper and 2.9inch e-Paper (D), partial refresh is supported. You can set Mode = 0 for full refresh and Mode =1 for partial refresh
void EPD_xxx_Init(UBYTE Mode); 
For other e-Paper
void EPD_xxx_Init(void);
  • Trasmite one frame of e-Paper and display
For black/white e-Paper
void EPD_xxx_Display(UBYTE *Image);
For three-color e-Paper
void EPD_xxx_Display(const UBYTE *blackimage, const UBYTE *ryimage);
There are exception:
For 2.13inch e-Paper (D) and 2.13inch e-Paper (D), if you want to do partial refresh, you should use function
void EPD_2IN13D_DisplayPart(UBYTE *Image);
void EPD_2IN9D_DisplayPart(UBYTE *Image);
For 1.54inch e-Paper V2 and 2.13inch e-Paper V2. you should first display static background (base image) and then dynamicly display (display Part) when partial refresh.
void EPD_1IN54_V2_DisplayPartBaseImage(UBYTE *Image);
void EPD_1IN54_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPart(UBYTE *Image);
void EPD_2IN13_V2_DisplayPartBaseImage(UBYTE *Image);
  • Sleep mode
void EPD_xxx_Sleep(void);
To wake up module, you should set hardware reset (re power on it) or call the init function.

GUI Functions

GUI files can be found in RaspberryPi&JetsonNano\c\lib\GUI\GUI_Paint.c(.h) directory

E-paper Driver HAT GUI.png

The fonts can be found in RaspberryPi&JetsonNano\c\lib\Fonts directory

E-paper Driver HAT Fonts.png
Create an image buffer
void Paint_NewImage(UBYTE *image, UWORD Width, UWORD Height, UWORD Rotate, UWORD Color)
  • Image: the Image buffer
  • Width: width of the image
  • Height: Height of the image
  • Rotate: Rotate angle
  • Color: Color of the image
Select image buffer
void Paint_SelectImage(UBYTE *image)
  • The image buffer, it is a pointer of image buffer's first address
Rotate image
This function should be used after Paint_SelectImage()
void Paint_SetRotate(UWORD Rotate)
  • Rotate: The angle rotated. It should be ROTATE_0, ROTATE_90, ROTATE_180, ROTATE_270
  • Note: For different orientation, the position of the first pixel is different, here we take 1.54inch as example

SPI-epaper-C-0.pngSPI-epaper-C-90.pngSPI-epaper-C-180.pngSPI-epaper-C-270.png

Mirroring
void Paint_SetMirroring(UBYTE mirror)
  • mirror: The type of mirroring. (MIRROR_NONE, MIRROR_HORIZONTAL、MIRROR_VERTICAL、MIRROR_ORIGIN)
Set Pixel
This function is used to set the position and types of the pixel
void Paint_SetPixel(UWORD Xpoint, UWORD Ypoint, UWORD Color)
  • Xpoint: The x-axis coordination of pixel
  • Ypoint: The y-axis coordination of pixel
  • Color: The color of the pixel
Clear
This function is used to clear the e-Paper
void Paint_Clear(UWORD Color)
  • Color: The color of the display
Clear window
This function is used to clear a partial area
void Paint_ClearWindows(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color)
  • Xstart: The x-axis coordination of the start point
  • Ystart: The y-axis coordination of the start point
  • Xend: The x-axis coordination of the end point
  • Yend: The y-axis coordination of the end point
  • Color: The color of the windows
Draw point

This function is used to draw points.

void Paint_DrawPoint(UWORD Xpoint, UWORD Ypoint, UWORD Color, DOT_PIXEL Dot_Pixel, DOT_STYLE Dot_Style)
  • Xpoint: The x-axis coordination of point
  • Ypoint: The y-axis coordination of point
  • Dot_Pixel: The size of the point
 	 	 typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  , 	 	// 3 X 3
 	 	 	 DOT_PIXEL_4X4  , 	 	// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
  • Dot_Style: The style of the point
 	 	typedef enum {
 	 	   DOT_FILL_AROUND  = 1,		
 	 	   DOT_FILL_RIGHTUP,
 	 	} DOT_STYLE;
Drawn Line
void Paint_DrawLine(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, LINE_STYLE Line_Style , LINE_STYLE Line_Style)

This function is used to draw a line

  • Xstart: The start x-axis coordination of the line
  • Ystart: The start y-axis coordination of the line
  • Xend: The end x-axis coordination of the line
  • Yend: The end y-axis coordination of the line
  • Line_width: The width of the line
 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
  • Line_style: The style of the line
 	 	typedef enum {
 	 	 	 LINE_STYLE_SOLID = 0,
 	 	 	 LINE_STYLE_DOTTED,
 	 	} LINE_STYLE;
Draw rectangle

Draw a rectangle from (Xstart, Ystart) to (Xend, Yend).

void Paint_DrawRectangle(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend, UWORD Color, DOT_PIXEL Line_width, DRAW_FILL Draw_Fill)
  • Xstart: Start coordinate of X-axes of the rectangle
  • Ystart: Start coordinate of Y-axes of the rectangle
  • Xend: End coordinate of X-end of the rectangle
  • Yend: End coordinate of Y-end of the rectangle
  • Color: color of the rectangle
  • Line_width: The width of edges, 8 sides are available;
 	 	typedef enum {
 	 	 	 DOT_PIXEL_1X1  = 1,	// 1 x 1
 	 	 	 DOT_PIXEL_2X2  , 		// 2 X 2
 	 	 	 DOT_PIXEL_3X3  ,		// 3 X 3
 	 	 	 DOT_PIXEL_4X4  ,		// 4 X 4
 	 	 	 DOT_PIXEL_5X5  , 		// 5 X 5
 	 	 	 DOT_PIXEL_6X6  , 		// 6 X 6
 	 	 	 DOT_PIXEL_7X7  , 		// 7 X 7
 	 	 	 DOT_PIXEL_8X8  , 		// 8 X 8
 	 	} DOT_PIXEL;
 	

  • Draw_Fill: set the rectangle full or empty.
typedef enum {
 	DRAW_FILL_EMPTY = 0,
 	DRAW_FILL_FULL,
} DRAW_FILL;
Draw character (ASCII)

Set(Xstart Ystart) as letf-top point, draw a ASCII character.

void Paint_DrawChar(UWORD Xstart, UWORD Ystart, const char Ascii_Char, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

  • Xstart: X coordinate of the left-top pixel of character;
  • Ystart: Y coordinate of the left-top pixel of character;
  • Ascii_Char:Ascii character;
  • Font: 5 fonts are available;
    font12:7*12
    font16:11*16
    font20:14*20
    font24:17*24
  • Color_Foreground: color of character;
  • Color_Background: color of background;
Draw String

Set point (Xstart Ystart) as the left-top pixel, draw a string.

void Paint_DrawString_EN(UWORD Xstart, UWORD Ystart, const char * pString, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

  • Xstart: X coordinate of left-top pixel of characters;
  • Ystart: Y coordinate of left-top pixel of characters;
  • pString:Pointer of string
  • Font: 5 fonts are available:
    font8:5*8
    font12:7*12
    font16:11*16
    font20:14*20
    font24:17*24
  • Color_Foreground: color of string
  • Color_Background: color of the background
Draw Chinese characters

this function is used to draw Chinese fonts based ON GB2312 fonts.

void Paint_DrawString_CN(UWORD Xstart, UWORD Ystart, const char * pString, cFONT* font, UWORD Color_Foreground, UWORD Color_Background)

Parameters:

  • Xstart: Coordinate of left-top pixel of characters;
  • Ystart: Coordinate of left-top pixel of characters;
  • pString:Pointer of string;
  • Font: GB2312 fonts:
    font12CN:11*21(ascii),16*21 (Chinese)
    font24CN:24*41(ascii),32*41 (Chinese)
  • Color_Foreground: color of string
  • Color_Background: color of the background
Draw number

Draw a string of numbers, (Xstart, Ystart) is the left-top pixel.

void Paint_DrawNum(UWORD Xpoint, UWORD Ypoint, int32_t Nummber, sFONT* Font, UWORD Color_Foreground, UWORD Color_Background)

Parameter:

  • Xstart: X coordinate of left-top pixel;
  • Ystart: Y coordicate of left-to pixel;
  • Nummber: the numbers displayed. the numbers are saved in int format, the maximum is 2147483647;
  • Font: 5 fonts are available:
    font8:5*8
    font12:7*12
    font16:11*16
    font20:14*20
    font24:17*24
  • Color_Foreground: color of font;
  • Color_Background: color of background;
Draw image

Send image data of BMP file to buffer

void Paint_DrawBitMap(const unsigned char* image_buffer)

Parameters:

  • image_buffer: adrress of image data in buffer
Read local bmp picture and write it to buffer

Linux platform like Jetson Nano and Raspberry Pi support to directly operate bmp pictures Raspberry Pi & Jetson Nano:RaspberryPi&JetsonNano\c\lib\GUI\GUI_BMPfile.c(.h)

UBYTE GUI_ReadBmp(const char *path, UWORD Xstart, UWORD Ystart)

Parameters:

  • path:The path of BMP pictures
  • Xstart: X coordination of left-top of picture, default 0;
  • Ystart: Y coordination of left-top of picture, default 0;

Testing Code

In the above part, we describe the tree structures of Linux codes, here we talk about the testing code for user. Raspberry Pi & Jetson Nano: RaspberryPi_JetsonNano\c\examples. The codes in examples are testing code, you can modify the definition in main.c file for different types of e-paper. For example, if you want to test the 2.13inch e-paper, you need to delete the "//" symbol on line 32. Use 5.65inch e-Paper as an example, you need to change the line:

//EPD_5in65f_test();

to

EPD_5in65f_test();

Then compile it again and run

make clean
make
sudo ./epd

Python (Can be used for Jetson nano and Raspberry Pi)

It is compatible with python2.7 and python3
python is easy to use than c codes
Raspberry Pi and Jetson Nano:RaspberryPi&JetsonNano\python\lib\

epdconfigu.py

  • Initialize module and exit handle:
def module_init()
def module_exit()

Note:
1. The functions are used to set GPIP before and after driving e-Paper
2. If the board you have is printed with Rev2.1, the module enter low-ultra mode after Module_Exit(). (as we test, the current is about 0 in this mode);

  • GPIO Read/Write:
def  digital_write(pin, value)
def  digital_read(pin)
  • SPI Write data:
def spi_writebyte(data)

epdxxx.py(xxx is the type of e-Paper)

  • Initailize e-paper: this function should be used at the begining. It can also be used to wake up e-Paper from Sleep mode.
#For 2.13inch e-Paper、2.9inch e-Paper
def init(self, update) #  Choose lut_full_update or lut_partial_update
#Other type
def init(self)
  • Clear e-paper: This function is used to clear e-Paper to white;
def Clear(self)
def Clear(self, color) # Some types of e-Paper should use this function to clear screen
  • Convert image to arrays
def getbuffer(self, image)
  • Transmit one frame of image data and display
#For two-color e-paper
def display(self, image)

#Because that controllers of 2.13inch e-paper are updated, when partial refresh, they should first use displayPartBaseImage() to display static background, then use displayPart() to dynamaticlly display.
def displayPartBaseImage(self, image)
def displayPart(self, image)
  • Enter sleep mode
def sleep(self)

epd_xxx_test.py(xxx is type of e-paper)

python examples are saved in directory:
Raspberry Pi and Jetson Nano:RaspberryPi&JetsonNano\python\examples\
If the python installed in your OS is python2, you should run examples like below:

sudo python epd_2in13_V2_test.py

If it is python3, the commands should be:

sudo python3 epd_2in13-V2_test.py

Orientation

To rotate the display, you can use transpose function like blackimage = blackimage.transpose(Image.ROTATE_270):

blackimage = blackimage.transpose(Image.ROTATE_270) 
redimage = redimage.transpose(Image.ROTATE_270)
#Support ROTATE_90, ROTATE_180, ROTATE_270

GUI

Python has a powerful PIL library, which can be used directly to drawing figures. Here we use it for drawing

  • Install the library firstly
sudo apt-get install python3-pil 

Import the library

from PIL import Image,ImageDraw,ImageFont

Image: library; ImageDraw: drawing function; ImageFont: fonts

  • Set image buffer for drawing.
image = Image.new('1', (epd.width, epd.height), 255)  # 255: clear the frame

The first parameter is the depth of color, 1 means 2 grayscale. The second parameter is a tuple of image size. The third parameter is color of the image, 0 is black and 255 is white.

  • Create an image object.
draw = ImageDraw.Draw(image)
  • Draw rectangle
draw.rectangle((0, 10, 200, 34), fill = 0)

The first parameter is a tuple of coordination. 0, 10 is the top-left point of rectangle, 200, 34) is the right-bottom point. fille = 0 set the filled color to black.

  • Draw line
draw.line((16, 60, 56, 60), fill = 0)

The first parameter is a type of coordination, 16, 60 is the beginning point, 200, 34 is the endpoint. fill=0 set the line to black

  • Draw circle
draw.arc((90, 60, 150, 120), 0, 360, fill = 0)

This function is used to draw a encircle of a square. The first parameter is a tuple of coordination of the square. the degree of the circle is 0 to 360 °, fille=0 set the circle to black.
If the figure is not square according to the coordination, you will get an ellipse.。

Besides the arc function, you can also use the chord function for drawing a solid circle.

draw.chord((90, 130, 150, 190), 0, 360, fill = 0)

The first parameter is the coordination of the enclosing rectangle. The second and third parameters are the beginning and end degrees of the circle. The fourth parameter is the fill color of the circle.

  • Character

You can directkt import ImageFont model for drawing characters:

font = ImageFont.truetype(os.path.join(picdir, 'Font.ttc'), 24)

You can use the fonts of Windows or other fonts which is in ttc format.

To draw English character, you can directly use the fonts; for Chinese character, you need to add a symbol u:

draw.text((8, 12), 'hello world', font = font, fill = 255)
draw.text((8, 36), u'电子墨水屏', font = font, fill = 0)

The first parameter is a tuple of coordination of character, the second parameter is the font and las one is set the color.

  • Read local picture
image = Image.open(os.path.join(picdir, '2in13-v2.bmp'))

The parameter is the path of picture.

  • Other functions.

For more information about the PIL library, please refer to http://effbot.org/imagingbook.