Difference between revisions of "Template:Jetson-nano-case-c-assembly"
From Waveshare Wiki
Line 1: | Line 1: | ||
==Jetson Nano Case (C) Assembly== | ==Jetson Nano Case (C) Assembly== | ||
− | ;Check the components before assembling. | + | ; Check the components before assembling. |
− | :[[File:Jetson-case-c-wiki-0.png| | + | :[[File:Jetson-case-c-wiki-0.png|600px]] |
− | ;Step 1: Remove the Jetson nano, assemble the wireless module and replace it. | + | ; Step 1: Remove the Jetson nano, assemble the wireless module and replace it. |
− | :[[File:Jetson-case-c-wiki-1.png| | + | :[[File:Jetson-case-c-wiki-1.png|600px]] |
− | ;Step 2: Mount the buttons on the metal box, note that the button with four wires is the Power button and another which has two wires are the Reset button. | + | ; Step 2: Mount the buttons on the metal box, note that the button with four wires is the Power button and another which has two wires are the Reset button. |
− | :[[File:Jetson-case-c-wiki-2.png| | + | :[[File:Jetson-case-c-wiki-2.png|600px]] |
− | ;Step 3:Connect buttons to Jetson Nano, please refer to the diagram. Insert the micro SD adapter board | + | ; Step 3:Connect buttons to Jetson Nano, please refer to the diagram. Insert the micro SD adapter board into the Micro SD slot of Jetson nano. Press it to let it lock. <big>'''Note that you should press the adapter to make sure that the adapter is pop-up, then remove it. You cannot directly pull it out, otherwise, you will break the Micro SD slot.'''</big> |
− | :[[File:Jetson-case-c-wiki-3.png| | + | *For Jetson Nano Developer Kit old version (A02) |
− | ;Step 4: Adjust the cables, mount the Jetson Nano developer Kit in the Metal box and fix it | + | :[[File:Jetson-case-c-wiki-14.jpg|600px]] |
− | :[[File:Jetson-case-c-wiki-4.png| | + | *For Jetson Nano Developer Kit B01 version |
− | ;Step 5: Fix the Jetson Nano GPIO adapter board in metal box by skews. | + | :[[File:Jetson-case-c-wiki-3.png|600px]] |
− | :[[File:Jetson-case-c-wiki-5.png| | + | ; Step 4: Adjust the cables, mount the Jetson Nano developer Kit in the Metal box and fix it with screws. You should also fix the Micro SD adapter board with a screw. |
− | ;Step 6: Fix the antennas of the wireless module on the metal box. Assemble the cooling fan. | + | :[[File:Jetson-case-c-wiki-4.png|600px]] |
− | :[[File:Jetson-case-c-wiki-6.png| | + | ; Step 5: Fix the Jetson Nano GPIO adapter board in the metal box by skews. |
− | ;Step 7: Connect Jetson nano to the GPIO adapter by cable. | + | :[[File:Jetson-case-c-wiki-5.png|600px]] |
− | :[[File:Jetson-case-c-wiki-7.png| | + | ; Step 6: Fix the antennas of the wireless module on the metal box. Assemble the cooling fan. |
− | ;Step 8: Fix the camera holder-bottom on the metal cover. | + | :[[File:Jetson-case-c-wiki-6.png|600px]] |
− | :[[File:Jetson-case-c-wiki-8.png| | + | ; Step 7: Connect Jetson nano to the GPIO adapter by cable. |
− | ;Step 9: Fix camera on camera holder-top | + | :[[File:Jetson-case-c-wiki-7.png|600px]] |
− | :[[File:Jetson-case-c-wiki-9.png| | + | ; Step 8: Fix the camera holder-bottom on the metal cover. |
− | ;Step 10: Assemble camera holders | + | :[[File:Jetson-case-c-wiki-8.png|600px]] |
− | :[[File:Jetson-case-c-wiki-10.png| | + | ; Step 9: Fix camera on camera holder-top with nylon screws. |
− | ;Step 11: Connect the cable cables to Jetson Nano (you can first remove it from cameras), If you have only one camera, just need to connect one cable. | + | :[[File:Jetson-case-c-wiki-9.png|600px]] |
− | :[[File:Jetson-case-c-wiki-11.png| | + | ; Step 10: Assemble camera holders with screws, adjust the angle and turn it tightly. |
− | ;Step 12: Assemble the case, connect the Camera and antennas. | + | :[[File:Jetson-case-c-wiki-10.png|600px]] |
− | :[[File:Jetson-case-c-wiki-12.png| | + | ; Step 11: Connect the cable cables to Jetson Nano (you can first remove it from cameras), If you have only one camera, just need to connect one cable. |
+ | :[[File:Jetson-case-c-wiki-11.png|600px]] | ||
+ | ; Step 12: Assemble the case, connect the Camera and antennas. | ||
+ | :[[File:Jetson-case-c-wiki-12.png|600px]] |
Revision as of 07:03, 20 January 2022
Jetson Nano Case (C) Assembly
- Check the components before assembling.
- Step 1
- Remove the Jetson nano, assemble the wireless module and replace it.
- Step 2
- Mount the buttons on the metal box, note that the button with four wires is the Power button and another which has two wires are the Reset button.
- Step 3
- Connect buttons to Jetson Nano, please refer to the diagram. Insert the micro SD adapter board into the Micro SD slot of Jetson nano. Press it to let it lock. Note that you should press the adapter to make sure that the adapter is pop-up, then remove it. You cannot directly pull it out, otherwise, you will break the Micro SD slot.
- For Jetson Nano Developer Kit old version (A02)
- For Jetson Nano Developer Kit B01 version
- Step 4
- Adjust the cables, mount the Jetson Nano developer Kit in the Metal box and fix it with screws. You should also fix the Micro SD adapter board with a screw.
- Step 5
- Fix the Jetson Nano GPIO adapter board in the metal box by skews.
- Step 6
- Fix the antennas of the wireless module on the metal box. Assemble the cooling fan.
- Step 7
- Connect Jetson nano to the GPIO adapter by cable.
- Step 8
- Fix the camera holder-bottom on the metal cover.
- Step 9
- Fix camera on camera holder-top with nylon screws.
- Step 10
- Assemble camera holders with screws, adjust the angle and turn it tightly.
- Step 11
- Connect the cable cables to Jetson Nano (you can first remove it from cameras), If you have only one camera, just need to connect one cable.
- Step 12
- Assemble the case, connect the Camera and antennas.