Template:Compute Module 4 PoE 4G Board manual

From Waveshare Wiki
Revision as of 13:28, 10 September 2021 by Waveshare-eng11 (Talk | contribs)

Jump to: navigation, search

Writing Image


The USB interfaces are default disabled in CM4, you need to enable it by adding the following lines:the config.txt



The USB to UART port is connected to GPIO14(BCM) and GPIO15(BCM) pins of CM4 with a converter.
You can connect the USB to UART port for login CM4 via serial.
The USB to UART port can also be used for power, in this case, you need to solder a 0ohm resistor to the pad for enabling the powering function.
Compute Module 4 PoE 4G Board 6.png



The buzzer is connected to GPIO22(BCM), low active.

Compute Module 4 PoE 4G Board 4.png


Two LEDs are integrated for users, the green one is connected to GPIO20(BCM)and the red one is connected to GPIO21(BCM), low active.

Compute Module 4 PoE 4G Board 5.png


To work with 4G/5G, you need to connect a wireless module to the M.2 B KEY for featuring corresponding functions. M.2 B KEY only extends USB2.0 interfaces, it doesn't support PCIe devices.
Compute Module 4 PoE 4G Board 3.png
SIM card is required to work with the 4G/5G module
This carrier board supports the 4G module by default, if you use it with 5G modules, some of the 5G functions are not supported.
If you use a 5G module, please check the [SIM8200EA-M2_5G HAT wiki] about how to set up 5G.

If you need to toggle the working status of the 4G module, you can control the GPIO6(BCM), set the GPIO6 to High for disabling the 4G module and set it to Low for enabling.
To toggle the working status of the 4G module, please add delay time for waiting for the operation to work.

SIM7600 M.2 module

Status of M.2 indicators:

Red LED Green LED Status
Solid OFF Power OFF
Solid OFF Starting
Solid Solid SIM card is an invalid or weak signal
Solid Blink Working
OFF Blink/Solid Shutdowning

Before you configure the SIM7600 module, please make sure that the module is started normally.

sudo apt-get install minicom
sudo minicom -D /dev/ttyUSB2

Type the following command on the minicom


Close the minicom and configure usb0

sudo dhclient -v usb0

About RNIDS networking, please refer to [Raspberry Pi networked via RNDIS RNIDS Networking method]
With the operations above, a USB0 port will be recognized.
If the network cannot work, please try to switch frequency with the following AT commands:


AT Commands

If the network cannot work, plaese check module with AT commands

sudo apt-get install minicom
sudo minicom -D /dev/ttyUSB2

Common AT commandsni

Command Description Return
AT AT test OK
ATE ATE1 enable echo
ATE0 disable echo
AT+CGMI Check manfacture OK
AT+CGMM Check module type OK
AT+CSUB Check module version OK
AT+CGMR Check firmware version OK
AT+IPREX Configure hardwara baud rate +IPREX:
AT+CRESET Reset module OK
AT+CSQ Check signal quanlity +CSQ: 17,99
AT+CPIN? Check SIM status +CPIN: READY
AT+COPS? CHeck the current supplier +COPS:
AT+CREG? Check network status +CREG:
AT+CPSI? Check UE information
AT+CNMP Configure network mode:
13:GSM only
38:LTE only
48 : Any modes but LTE
... ....

For more AT commands, please refer to: AT_Command_V2.00
You can also refer to:SIMCom


The PCIe interface is PCIe 2.0 X1, the maximum speed is 500Mb/s
Most of the PCIEx1 device is not supported by Raspberry Pi without a driver.
Please check your PCIe device before you used Supported device testing
Raspberry Kernel compiling