Difference between revisions of "Template:CM4-DUAL-ETH-BASE Spec"

From Waveshare Wiki
Jump to: navigation, search
Line 12: Line 12:
 
{|border=2; style="width:800px;"
 
{|border=2; style="width:800px;"
 
|-style="background:#efffff; color:blue;" align="center"
 
|-style="background:#efffff; color:blue;" align="center"
|style="width:58px"|No.||Component||Description
+
|style="width:58px"|标号||名称||说明
 
|-style="background:#00eecc; color:blue;" align="center"
 
|-style="background:#00eecc; color:blue;" align="center"
|-
+
|-align="center"
|1||CM4 socket||Suitable for all variants of Compute Module 4
+
|1||CM4 连接器||适用于 Compute Module 4 的所有版本
|-
+
|-align="center"
|style="width:66px"|2||40PIN GPIO header||~
+
|style="width:66px"|2||40PIN GPIO 接口||方便连接各种 HAT 模块
|-
+
|-align="center"
|3||BOOT selection ||ON: CM4 would be booted from USB-C interface <br> OFF: CM4 would be booted from eMMC or Micro SD card
+
|3||RJ45 千兆网口||O双路 RJ45 千兆网口,支持 10/100/1000M 网络接入<br />ETHERNET 0: CM4 原生网口<br />ETHERNET 1: USB 扩展网口
|-
+
|-align="center"
|4||Misc functional pins||~
+
|4||USB 3.2 接口||3 路 USB 3.2 Gen1 接口,支持各种 USB 设备插入
|-
+
|-align="center"
|5||USB Type-C power supply / programming||5V/2.5A power supply,<br>also allows burning system image into Compute Module 4 eMMC variants
+
|5||HDMI 接口||双路 HDMI 接口,支持双 4K 30fps 输出
|-
+
|-align="center"
|6||Status indicators||ACT: Raspberry Pi operating status indicator<br>PWR: Raspberry Pi power indicator
+
|6||CAM 接口||双路 MIPI CSI 摄像头接口
|-
+
|-align="center"
|7||DISP||2x MIPI DSI display port
+
|7||DC 供电接口||7~36V DC 宽电压供电
|-
+
|-align="center"
|8||CAM||2x MIPI CSI  camera connectors.
+
|8||双 LED 灯座||红灯:树莓派电源指示灯<br />绿灯:树莓派工作状态指示灯
|-
+
|-align="center"
|9||USB2.0 ports||4x USB2.0 ports, for connecting sorts of USB devices
+
|9||Micro SD 卡接口||用于接入带系统的 Micro SD 卡,以启动 Compute Module 4 Lite
|-
+
|-align="center"
|10||HDMI ports||2x HDMI ports, supports dual 4K 30fps output
+
|10||FAN 接口||方便接入散热风扇,支持调速和测速
|-
+
|-align="center"
|11||RTC battery holder||supports CR1220 button cell
+
|11||DISP0 接口||MIPI DSI 显示接口
|-
+
|-align="center"
|12||FAN header||for connecting cooling fan, allows speed adjustment and measurement
+
|12||USB SLAVE 接口||Compute Module 4 eMMC 版本可通过此接口烧录系统镜像
|-
+
|-align="center"
|13||PCIe Gen 2 × 1 socket|| forconnecting PCIe Gen 2 × 1 modules
+
|13||RTC 电池连接座||可接入 CR1220 纽扣电池
|-
+
|-align="center"
|14||Gigabit Ethernet connector||Gigabit Ethernet RJ45 with PoE support, 10/100/1000M compatible
+
|14||RTC 中断管脚切换||PI-RUN: RTC 触发中断 CM4 重启<br />GN-EN: RTC 触发中断 CM4 断电<br />D4: RTC 触发中断 D4 管脚
|-
+
|-align="center"
|15||DC 5V output||~
+
|15||IO-VREF 选择 ||CM4 IO 逻辑电压切换 3.3V 或者 1.8V
|-
+
|-align="center"
|16||RS485||with 600W lightning-proof, anti-surge, and 15KV ESD protection,<br>reversed optional 120R balancing resistor jumper
+
|16||FAN 供电选择||可选择 5V 或 12V 电压驱动风扇
|-
+
|-align="center"
|17||RS232||with TVS diode, anti-surge, and ESD protection
+
|17||系统功能切换||BT_DIS: 蓝牙禁用,仅供带天线的 CM4 版本使用<br />WiFi_DIS: WiFi 禁用,仅供带天线的 CM4 版本使用<br />WP_DIS: 启动方式切换,仅供不使用 EMMC 启动或 SD 启动的情况下使用
|-
+
|-align="center"
|18||Buzzer||~
+
|18||RTC/FAN I2C 总线选择||SDA0/SCL0: I2C-10 CSI/DSI 共用<br />GPIO3/2: I2C-1 40PIN 共用
|-
+
|-align="center"
|19||FAN_VDD/PoE selection||cooling fan driving voltage: 12V or 5V<br>PoE: enable (EN) or disable (DIS)
+
|19||RTL8153||USB 千兆网卡芯片
|-
+
|-align="center"
|20||FE1.1S||USB expansion chip
+
|20||EMC2301||风扇控制器,控制风扇转速,测量风扇转速
|-
+
|-align="center"
|21||PCF52063ATL||RTC chip
+
|21||VL805||USB 3.0 HUB
|-
+
||
|22||RTC/FAN||I2C bus switch,<br>SDA0/SCL0: I2C-10 is shared with CSI/DSI<br>GPIO3/2: I2C-1 is shared with 40PIN header
 
|-
 
|23||IO logic level selection||set the CM4 IO logic level as 3.3V or 1.8V
 
|-
 
|24||RTC interruption configuration||PI-RUN: CM4 will reboot on RTC interruption<br>GN-EN: CM4 powerdown on RTC interruption<br>D4: D4 pin is triggered on RTC interruption
 
|-
 
|25||Micro SD card slot||insert a Micro SD card with pre-burnt system, to start up Compute Module 4 Lite
 
 
|}
 
|}

Revision as of 11:45, 14 July 2021

Overview

CM4-DUAL-ETH-BASE is a base board that can be used with Raspberry Pi Compute Module 4, and supports 7~12V DC power supply, onboard three USB3.2, dual Gigabit Ethernet ports.

Dimension

Compute_Module 4 POE Board (B)
CM4-DUAL-ETH-BASE-details-size.jpg
Compute_Module 4
Compute Module 4 IO Board 5.png

What's on board

CM4-DUAL-ETH-BASE-details-intro.jpg

标号 名称 说明
1 CM4 连接器 适用于 Compute Module 4 的所有版本
2 40PIN GPIO 接口 方便连接各种 HAT 模块
3 RJ45 千兆网口 O双路 RJ45 千兆网口,支持 10/100/1000M 网络接入
ETHERNET 0: CM4 原生网口
ETHERNET 1: USB 扩展网口
4 USB 3.2 接口 3 路 USB 3.2 Gen1 接口,支持各种 USB 设备插入
5 HDMI 接口 双路 HDMI 接口,支持双 4K 30fps 输出
6 CAM 接口 双路 MIPI CSI 摄像头接口
7 DC 供电接口 7~36V DC 宽电压供电
8 双 LED 灯座 红灯:树莓派电源指示灯
绿灯:树莓派工作状态指示灯
9 Micro SD 卡接口 用于接入带系统的 Micro SD 卡,以启动 Compute Module 4 Lite
10 FAN 接口 方便接入散热风扇,支持调速和测速
11 DISP0 接口 MIPI DSI 显示接口
12 USB SLAVE 接口 Compute Module 4 eMMC 版本可通过此接口烧录系统镜像
13 RTC 电池连接座 可接入 CR1220 纽扣电池
14 RTC 中断管脚切换 PI-RUN: RTC 触发中断 CM4 重启
GN-EN: RTC 触发中断 CM4 断电
D4: RTC 触发中断 D4 管脚
15 IO-VREF 选择 CM4 IO 逻辑电压切换 3.3V 或者 1.8V
16 FAN 供电选择 可选择 5V 或 12V 电压驱动风扇
17 系统功能切换 BT_DIS: 蓝牙禁用,仅供带天线的 CM4 版本使用
WiFi_DIS: WiFi 禁用,仅供带天线的 CM4 版本使用
WP_DIS: 启动方式切换,仅供不使用 EMMC 启动或 SD 启动的情况下使用
18 RTC/FAN I2C 总线选择 SDA0/SCL0: I2C-10 和 CSI/DSI 共用
GPIO3/2: I2C-1 和 40PIN 共用
19 RTL8153 USB 千兆网卡芯片
20 EMC2301 风扇控制器,控制风扇转速,测量风扇转速
21 VL805 USB 3.0 HUB