SIM7600E-H 4G HAT
- 40PIN GPIO extension header for connecting Jetson Nano.
- Supports dial-up, telephone call, SMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.
- Supports GPS, BeiDou, Glonass, LBS base station positioning.
- Onboard USB interface, to test AT Commands, get GPS positioning data, and so on.
- Breakout UART control pins, to connect with host boards like Arduino/STM32.
- SIM card slot, supports 1.8V/3V SIM card.
- Onboard TF card slot, which can be used to store files, text messages and other data.
- Onboard audio jack and audio decoder chip, for making telephone calls.
- 2 x LED indicators, easy to monitor the working status.
- Onboard voltage translator, the operating voltage can be configured to 3.3V or 5V via jumper.
- Baudrate: 300bps ~ 4Mbps (default: 115200bps)
- Autobauding baudrate: 9600bps ~ 115200bps.
- Provide complete supporting manuals (example programs such as Raspberry/Jetson Nano/Arduino/STM32).
|LTE Cat-1||not support||10Mbps(DL)
|2G (EDGE)||236.8Kbps(DL)/236.8Kbps(UL)||not support||236.8Kbps(DL)/236.8Kbps(UL)|
|2G (GPRS)||85.6Kbps(DL)/85.6Kbps(UL)||not support||85.6Kbps(DL)/85.6Kbps(UL)|
|USB Driver||Windows XP/7/8/10、Linux (RPi Raspbian System driver free)|
|SIM Card Slot||Both are supported, compatible with 1.8V and 3V SIM cards|
|UART Interface||Both are supported, the serial port sends and receives AT commands, and is compatible with 3.3V/5V working level|
|USB Interface||Both are supported and can be used to test AT commands, obtain GPS positioning information, upgrade firmware, etc.|
|USB to UART||Both are supported and can be used for serial port debugging or logging in to Raspberry Pi|
|Audio Port||Both are supported and can be used for voice operations such as making calls|
|TF Card Slot||Support, can be used to store files, text messages and other data||Not Support||Support|
|Antenna interface||LTE main antenna||LTE Main Antenna + LTE Diversity Antenna + GNSS Antenna|
|Applicable area||China||Europe/Southeast Asia/West Asia/Africa
|North America||Used globally|
|Typical application||Medical and health, smart payment, public network intercom, environmental monitoring, energy monitoring, fleet management, smart industry, smart agriculture|
- In addition to the micro USB cable, LTE antenna, and GPS antenna, users need to prepare the following items before using the module:
A 4G SIM card (no downtime and GPRS enabled); A headphone cable with a microphone (optional); A TF card (optional);
- When power off, insert the activated 4G SIM card, TF card (optional), insert the headphone cable with microphone (optional), and then connect the USB cable to the computer.
- Hardware connection diagram:
- Back Connection Diagram
Hardware Configration of the New Version
In the second half of 2021, the SIM7600 series boards will be switched to new versions for shipment. The old and new versions can be used normally and stably.Compared with the old version, the new version has the following changes:
- 1) Newly added 330uF electrolytic capacitor (Stronger voltage stabilization ability)
- 2) Newly added PWR and Flightmode pin jumpers (Automatic power-on function can be set, and the IO port can be customized to control the switch and Flight mode)
- 3) Add solderable pads for VCCIO.(when used with Raspberry Pi, the SIM7600X 4G HAT is soldered at 3.3V working level by default; if you need to use 5V working-level MCU, you can change it to 5V by yourself)
- 4) Add solderable pads for the module USB. (if you don’t want to use a USB adapter cable, you can solder them to the corresponding USB solder joints at the bottom of the Raspberry Pi through some flying cables. This operation should be used with caution by non-professionals)
- 5) The power management IC was changed from MP1482 to SPX29302
- 6) The silkscreen naming is changed from "WPI naming" to "BCM naming"
- 7) Fine-tuning the layout
- 8) Add new solder joints for module Boot to burn the firmware forcibly. Short-circuit the two pads can enter the forced firmware burning mode. (Only used when the firmware cannot be burned normally)
Description of turning on/off the HAT for New Version
- In the new version, PWR and 3V3 are short-circuited by default, so the HAT turned on automatically after connecting to the power supply.
- If you need to use the PWRKEY button to turn on/off the HAT, please remove the jumper cap between PWR and 3V3:
- If you want to use the Raspberry Pi to turn on/off, please set the jumper cap between PWR and D6:
Flight mode description of the New Version
- The new version of the HAT doesn't turn on the Flight mode by default:
- If you need to control the Flight mode through the Raspberry Pi pins, set the jumper cap between Flight and D4:
Net Indicator Working Status
- Test environment: Windows operating system
- Test software: SIM7600 serial port debugging assistant
- Driver file: SIM7600X driver file
1.Download Driver: SIM7600X driver
2.Insert the 4G HAT into the Windows computer as shown in the hardware connection diagram above (the Windows 10 operating system is used as an example below) 3.Make sure the module has been powered on normally: refer to the previous chapter "Switching on and off the module"
4. Unzip the driver file --> Double-click the exe driver file with the left mouse button --> Select the installation path --> NEXT --> Wait for the installation to complete --> Restart the computer --> Complete the driver installation.
- After installation, all the devices should be recognized normally as below:
- After installation, all the devices should be recognized normally as below:
Common AT Command
- SIM7600X module supports AT command control, some basic AT commands are shown in the table below:
(For the complete AT command set, please refer to: For more AT commands, please refer to: SIM7600X series AT command set)
|AT||AT Test Command||OK|
|ATE||ATE1 set echo
ATE0 close echo
|AT+CGMI||Query module manufacturer||OK|
|AT+CGMM||Query module model||OK|
|AT+CGSN||Query product serial number||OK|
|AT+CSUB||Query module version and chip||OK|
|AT+CGMR||Query the firmware version serial number||OK|
|AT+IPREX||Set the module hardware serial port baud rate||+IPREX:|
|AT+CSQ||Network signal quality query, return signal value||+CSQ: 17,99|
|AT+CPIN?||Query the status of the SIM card and return READY, indicating that the SIM card can be recognized normally||+CPIN: READY|
|AT+COPS?||Query the current operator, the operator information will be returned after normal networking||+COPS:|
|AT+CREG?||Query network registration status||+CREG:|
|AT+CPSI?||Query UE system information|
|AT+CNMP?||Network mode selection command：
48 ： Any modes but LTE
AT command sending and receiving test
- Download serial debugging assistant: SIM7600 serial debugging assistant
- Open the device manager, find the port number corresponding to AT Port; then open the sscom software, select the corresponding port and baud rate, check "Add carriage return and line feed"; click the sscom "Extension" button and pull out the preset It is best to open the serial port and send the corresponding AT command to test. The test screenshot is shown below:
- Usually, when we use the Windows 10 operating system, make sure that the hardware and software drivers are installed. After the module is powered on, the PWR light is on normally, the NET light is flashing normally, and it will automatically connect to the Internet. If the Internet cannot be automatically connected, we can also use NDIS or PPPD to connect to the Internet
The steps for Windows NDIS dialing are as follows:
1. Open the SIM7600 AT port, and send the command (if using SSCOM to generate AT command, you must check "Enter")
AT$QCRMCALL=1,1 //must press "Enter"
2. At this point, the NDIS dialing takes effect, and the computer can connect to the network.
- Insert the module into the Raspberry Pi, and connect the USB interface to the USB port of the Raspberry Pi, turn it on, and the hardware is as shown below:
- Refer to "Raspberry Pi initialization settings" below, The Raspberry Pi does the initial setup.
- For dial-up Internet access, refer to the following operation video (for dial-up Internet access, it is recommended to use a USB interface connection, which is faster):
- PPPD dial-up
- After dialing up the Internet, if the DNS cannot be resolved and the Internet cannot be accessed, you can add the command:
route add -net 0.0.0.0 ppp0
- Plug in the GPS antenna, and place the receiver in an open space (note that it cannot be tested in rainy weather). It takes about 1 minute to receive the positioning signal after power-on;
- AT Command
AT+CGPS=1 //Open GPS AT+CGPSINFO //Print GPS information to serial port AT+CGPS=0 //close GPS
- SSCOM Software Test:
TCP/IP Network Data
GPRS debugging requires a SIM card with GPRS networking function enabled
We takes accessing a mobile SIM card as an example:
Correctly install the mobile phone card (the GPRS networking function must be enabled), the GSM antenna, and connect the USB cable to the computer; Press the PWR key to start the module and wait for more than ten seconds;
Observe whether the indicator light is normal, the PWR indicator is always on, and the NET indicator is flashing;
Set up a local computer virtual server
The virtual server defines the mapping relationship between the WAN service port and the LAN network server. All access to the WAN service port will be relocated to the LAN network server specified by the IP address. (Please refer to your router's corresponding manufacturer's manual)
Use a browser to log in to the router management interface (please refer to your router manual for the specific address)
Set the port number: 2317 (it does not conflict with the existing port number. In this example, it is set to 2317)
Set the intranet IP of the computer (the IP obtained by the computer in the local area network can be run CMD on the local machine, enter the command line prompt, enter ipconfig to view the IPv4 address, the intranet IP of the computer in this example is 192.168.1.168), as shown in the following figure :
Set up GPRS
AT+CGDCONT=1,"IP","CMNET" //Set APN AT+CSQ //Query the network signal quality, the first parameter is the maximum network signal quality is 31, the larger the value, the stronger the network signal AT+CREG? //Query the network registration status, where the second parameter is 1, it means the registration has been successful AT+CIPMODE=1 //Set TCP/IP mode AT+CSOCKSETPN=1 //Select TCP/IP application mode AT+CIPMODE=0 //Select TCP/IP application mode AT+NETOPEN //Open mode AT+CIPOPEN=0,"TCP","220.127.116.11",2317 //Set TCP, IP and port number to establish TCP/IP connection AT+CIPSEND=0,9, //To specify to send 9 characters of data, return > to start sending 9 characters of content AT+CIPCLOSE=0, //Close the TCP connection AT+NETCLOSE, //Close the network
TF Card Debugging
1. Insert the TF card when the power is off (press the pop-up), follow the normal boot steps, and select the port number:
2. Select the TF card directory as the current directory
AT+FSCD=D: //Select TF card path +FSCD: D:/ OK AT+FSLS //View subdirectories +FSLS: SUBDIRECTORIES: overlays MyDir System Volume Information ... ... OK
3.Create a folder with content on the TF card. Use the statement to set the MyDir folder in the root directory and create a t1.txt file in the folder, and write the content test content at the same time
AT+CFTRANRX="D:/MyDir/t1.txt",12 //File name >test content //Content OK
4.Open TF Card
For more information, please refer to SIM7600X AT Commands
- Refer to the "Hardware Configuration" chapter to connect the LTE antenna, SIM card (the phone function must be enabled) and the headset cable with microphone, and the module is turned on.
- Common commands for making calls:
|AT+CNUM||Query the phone number (not all SIM cards support this command)||+CNUM|
|AT+CSDVC||AT+CSDVC=1: switch to headphone output
AT+CSDVC=3: switch to speaker output
|AT+CLVL=?||Query volume range||OK|
|AT+CLVL=2||Set volume to 2||OK|
|ATD<phone_number>;||ATD10086; : Dial the customer service number of Mobile 10086||OK|
|AT+CLIP=1||Set Caller ID||OK|
|ATA||Answer the call||OK|
- The detailed operation screenshots are as follows:
Voice output mode and volume adjustment
AT+CSDVC=1 //Switch to headset AT+CSDVC =3 //Switch to speaker AT+CLVL =? //Query the volume range, return +CLVL: (0-5) //Indicates that the volume is adjustable from 0 to 5 AT+CLVL=2 //Set the volume to 2, return OK
Answer the call
Incoming call serial display: RING send "ATA" // answer the call Send "AT+CHUP" //hang up
Audio parameter debugging
AT+CACDBFN=? +CACDBFN: (Handset_cal.acdb,Handset_tianmai.acdb) // It is recommended to consider setting this set of parameters OK
A. In the initialization stage of the module startup, before making a call, add the following
AT^PWRCTL=0,1,3 // Mainly improve TDD noise effect OK
B. The module is in the process of establishing a voice call
VOICE CALL:BEGIN // The module call is established and executed to improve the call effect AT+CECM=1 //Echo suppression processing OK AT+CECH=0x500 //Improve the volume effect of the mobile phone OK
SMS sending and receiving
Send English SMS
1. Install the SIM card and LTE antenna, connect the module's USB interface to the computer with a USB cable, and turn on the module;
2. Observe whether the indicator light is normal, the PWR indicator is always on, and the NET indicator is flashing;
3. Set the local SMS center: AT+CSCA="+8613800755500"+Enter, return OK.
4. AT+CMGF=1: Set the SMS mode to TEXT;
5. AT+CMGS=" phone number "<Enter>, set the recipient's mobile phone number, and then return: ">", send the desired content, such as "Send message test!", no need to enter at the end, after editing the text message Send 1A to send information in hexadecimal format (1A is the key value of "CTRL+Z", which is used to tell the module to execute the sending operation, or 1B or "ESC" to cancel the operation), after successful sending, the module returns + CMGS: 15 Confirmation that the transmission was successful. As shown below.
Receive English SMS
1. Send a message on the phone: "This is a receive test for SIM7600X!" to the test module
2. When receiving the information, the serial port will report the information, "SM", 20, which means there are 20 pieces of information in the SM, and the message just sent is the 20th piece of information.
3. Read information: AT+CMGR=20 to read the 20th information (AT+CMGL="ALL" to read all information)
4. Delete information: AT+CMGD=20, as shown below
5. Convert the displayed information to text through a code converter.
Send Chinese SMS
1. Set the parameters for sending SMS
AT+CMGF=1 //Set to text mode AT+CSCS="UCS2" //Set the message text to UCS2 encoding set AT+CSMP=17,167,2,25 //Set text mode parameters. AT+CMGS="00310033003400330032003100310039003100300031" //Set the UCS2 set of the receiver's mobile phone number;
2. Waiting to return to >, at this time send the converted information content (00530049004D003700360030003000584E2D658777ED4FE16D4B8BD5), no carriage return is required at the end, after editing the SMS, send 1A to send the message in hexadecimal format, as follows As shown:
Receive Chinese SMS
1. Set SMS receiving parameters
AT+CMGF=1 //Set text display AT+CSCS="GSM" //Set GSM code set AT+CNMI=2,1 //Set new information reminder
2. When receiving the information, the serial port will automatically report the information, and read the returned 21st information as shown in the figure below:
AT+CMGR=21 //Read the SMS content of serial number 21
SIM7600X 4G HAT has onboard Raspberry Pi GPIO interface, which can be directly inserted into various versions of Raspberry Pi; the following table shows the connection between Raspberry Pi pins and module pins (Raspberry Pi 3rd Generation B+):
|SIM7600X 4G HAT||Raspberry Pi|
|RXD||TXD (corresponding to 14 of BCM)|
|TXD||RXD (corresponding to 15 of BCM)|
|PWR||P22 (corresponding to P6 of BCM)|
|FLIGHTMODE||P7 (corresponding to P4 of BCM), enter flight mode when pulled high|
Raspberry Pi initialization settings
In order to ensure that the SIM7600X 4G HAT can work normally after being connected to the Raspberry Pi, it is necessary to initialize the level output of some pins of the Raspberry Pi. The specific operations are as follows:
- Download sample program, after decompression, rename the c folder under the Raspberry folder to SIM7600X, Then copy the entire SIM7600X folder to the Raspberry Pi /home/pi directory,
- The command line enters the /home/pi/SIM7600X directory and executes the command
chmod 777 sim7600_4G_hat_init
- Set the boot initialization script, run the command:
sudo nano /etc/rc.local
- Add before exit 0 (as shown below):
Raspberry Pi serial port configuration
Since the Raspberry Pi serial port is used for terminal debugging by default, if you need to use the serial port, you need to modify the Raspberry Pi settings. Execute the following command to enter the Raspberry Pi configuration:
Select Interfacing Options ->Serial ->no -> yes to disable serial debugging
Open the /boot/config.txt file, find the following configuration statement to enable the serial port, if not, add it at the end of the file:
Restart to take effect
Raspberry Pi minicom serial port debugging
1. Insert the module into the Raspberry Pi
2. Install minicom, minicom is a serial debugging tool for linux platform:
sudo apt-get install minicom
3. Execute minicom -D /dev/ttyS0 (ttyS0 is the serial port of Raspberry Pi 3B/3B+/4B).
Default baud rate is 115200
Raspberry Pi 2B/zero, the user serial device number is ttyAMA0, and the Raspberry Pi 3B/3B+/4B serial device number is ttyS0.
4. Take the AT synchronization test as an example, send relevant commands, as shown in the following figure:
* minicom can enter setting mode by pressing Ctrl+A, then Z, and select X to exit.
1. Insert the module into the Raspberry Pi
2. Download the sample program to the /home/pi/ path;
wget https://www.waveshare.net/w/upload/2/29/SIM7600X-4G-HAT-Demo.7z sudo apt-get install p7zip-full 7z x SIM7600X-4G-HAT-Demo.7z -r -o/home/pi sudo chmod 777 -R /home/pi/SIM7600X-4G-HAT-Demo
3. Go to the bcm2835 directory, compile and install it
chmod +x configure && ./configure && sudo make && sudo make install
Note: If there is a problem with the compilation, please refer to the instructions in the FAQ.
4. Go to the corresponding instance directory, compile and run the program. The relevant instructions are as follows (take the PhoneCall program as an example):
sudo make clean //Clear the original executable file sudo make //recompile sudo ./PhoneCall //Run the program
Use a combination of the above commands:
sudo make clean && sudo make && sudo ./PhoneCall
PHONECALL call demo
SMS text message sending and receiving demo
GPS Positioning Demo
TCP network communication demo
FTP download and upload demos
Hardware connection to the development board UNO PLUS / Arduino UNO:
|SIM7600X 4G HAT||UNO PLUS / Arduino UNO|
Install Arduino library
Download the decompression sample program,
Copy the Waveshare_SIM7600X_Arduino_Library folder to the Library directory under the Arduino IDE installation path
Open Arduino IDE --> File -->Examples -->Waveshare SIM7600X, and then choose to run the corresponding example program:
PHONECALL call demo
SMS text message sending and receiving demo
GPS Positioning demo
TCP network communication demo
FTP download and upload demo
Jetson Nano Demo
Jetson Nano has an onboard RaspberryPi 40Pin GPIO interface, SIM7600X 4G HAT can be directly connected and used, and Jetson Nano's terminal access the serial port does not affect serial communication with SIM7600X 4G HAT (ie Pin10 and Pin8).
|SIM7600X 4G HAT||Jetson Nano|
|TXD||10 (Board encoding)|
|RXD||8 (Board encoding)|
|PWR||31 (Board code)|
Jetson Nano minicom serial port debugging
1. Connect the SIM7600X 4G HAT to the Jetson Nano, press the PWRKER button for three seconds and then turn it on
2. Use SERIAL to log in to the Jetson Nano terminal, install minicom, and enter:
sudo apt-get install minicom
3. Run minicom to debug the serial port, and enter in the terminal
sudo minicom -D /dev/ttyTHS1 -b 115200
4. Send the AT command to test, press the PWRKEY button for three seconds to start the shutdown, exit the minicom and press Ctrl+A, then X, and finally press ENTER
After installing the library
sudo apt-get install python3-pip sudo pip3 install pyserial sudo apt-get install p7zip
Use the wget tool to download the source code to the specified folder of Jetson Nano, and copy the following command
mkdir -p ~/Documents/SIM7600X_4G_HAT wget -P ~/Documents/SIM7600X_4G_HAT/ http://www.waveshare.com/w/upload/2/29/SIM7600X-4G-HAT-Demo.7z
Enter the directory where the source code was just created and downloaded, and use the p7zip tool to unzip it to the current directory
cd ~/Documents/SIM7600X_4G_HAT/ sudo p7zip --uncompress SIM7600X-4G-HAT-Demo.7z
SIM7600X_4G_HAT is connected to Jetson Nano, connected to the antenna, the demo uses the software to power on and off, there is no need to press the button to power on and off, and when you exit, press Ctrl+C to power off the software. Enter the Jetson Nano/AT directory and execute the command:
cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/AT/ sudo python3 AT.py
SIM7600X_4G_HAT is connected to Jetson Nano and GNSS antenna. The routine uses software to power on and off. There is no need to press the button to power on and off. When exiting, press Ctrl+C to power off the software. Enter the Jetson Nano/GPS directory and execute the command:
cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/GPS/ sudo python3 GPS.py
SIM7600X_4G_HAT is connected to Jetson Nano, main antenna and earphone. The demo uses software to power on and off, no need to press the button to switch on and off. This demo uses mobile card to automatically dial 10086. Press Ctrl+C when exiting, and the software will start Shut down. Enter the Jetson Nano/PhoneCall directory and execute the command:
cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/PhoneCall/ sudo python3 PhoneCall.py
The SIM7600X_4G_HAT is connected to the Jetson Nano and the main antenna. The demo uses the software to turn it on and off, and there is no need to press the button to turn it on and off. This demo will automatically shut down the software after sending the information www.waveshare.com to the specified number. When users use SMS routines, they must first use tools such as vim to change the number in line 10 of the SMS.py file, replace * with a number, keep the ' symbol, How to use vim.
Enter the Jetson Nano/SMS directory and execute the command:
cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/SMS/ sudo python3 SMS.py
The SIM7600X_4G_HAT is connected to the Jetson Nano and the main antenna. The demo uses the software to turn it on and off, and there is no need to press the button to turn it on and off.
Enter the Jetson Nano/TCP directory and execute the command:
cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/TCP/ sudo python3 TCP.py
More sample programs are continuously updated...
- SIM7600 driver
- CP2102 driver
- SIM7600 Serial Debug Assistant
- GPS Debug Tool
- TCP Test Tool
- VLC media player
- Unicode Conversion Software
In this case, it may be that you have not successfully connected to the network, you can follow the steps below to troubleshoot:
1. First check the hardware connection:
- Check if the MAIN antenna is well connected;
- Whether the connected SIM card can call and surf the Internet normally on mobile phones and other devices:
- If the Raspberry Pi is connected, whether the module enters airplane mode;
2. After confirming that there is no problem with the hardware, the software can use these instructions:
- Check whether the sim card is in good contact: AT+CPIN?
- Check if the network mode setting is correct: AT+CNMP?
- Check the signal quality of the current environment: AT+CSQ
- Check the operator's access situation: AT+COPS?
- Check the connection status: AT+CPSI?
- Check whether it is successfully registered to the network: AT+CGREG?
Restart SIM7600E-H after sending the following commands:
This problem is generally caused by poor contact between the SIM card and the SIM card socket of the module.
It may be that the APN has not been obtained. Generally, the APN can be obtained automatically. In some areas (IoT card), it needs to be obtained manually. For example, it can be set by the following instructions:
AT+CGDCONT=1,"IP","APN" //The APN of different operators is different, here the APN is changed to the corresponding operator, for example: China Mobile APN: CMNET; China Unicom APN: 3GNET; China Telecom APN: CTNET
It can be set by the following commands:
AT+CGDCONT=1,"IPV6","APN" //Switch to IPV6, the APN of different operators is different, pay attention to distinguish the settings AT+CGDCONT=1,"IP","APN" //Switch back to IPV4
- No APN is set, configure APN as described above.
- After being banned, high-traffic (real-name IoT) cards are bound by chance cards and can only be used on one device (Ministry of Industry and Information Technology, Ministry of Public Security, must be issued to operators); The operator checks the status of the card and unlocks it.
The VOLTE function can be turned on with the following command:
The VOLTE function can be turned off with the following command:
The AUX antenna can increase the downlink rate: The AUX antenna is also a diversity antenna, which plays the role of receiving signals, improves the signal reception capability, and works with the MAIN antenna to increase the downlink rate.
- Under normal circumstances, SIM7600X has been automatically dialed after receiving the Windows system, and there is no need to repeat dialing. Repeated dialing will return NO CARRIER
- If you still can't dial-up Internet access, please use the following command to change to Windows default dial-up Internet access mode
- The display is turned off, the mobile network is not enabled, you can ignore it and go online directly;
- You can also install the driver SIM7600X dial-up Driver to update the network card
- The network card display is enabled after installing the driver
- Generally, the default configuration of SIM7600 is to automatically select the network standard, and it is likely to choose 2G Internet access; if you need to force the use of 4G mode, you need to enter the following AT command configuration:
AT+CNMP=38 //Fixed 4G LTE, if there is no local 4G coverage, you may not be able to register to the network
- If 4G has been fixed, the speed is still not ideal, it may be a frequency band problem;
AT+CNBP? //Back up the current frequency band (the returned frequency band information can be copied to notepad, etc.)
AT+CNBP=0x0002000000400183,0x000001E000000000,0x0000000000000021 //After returning OK, measure the speed
AT+CNBP=0x0002000004400180,0x000001E000000000,0x000000000000003F //If the speed does not improve, try this
1. Pay attention to check the device manager, the new device will be prompted during the upgrade process, and there will be no device driver during the first upgrade;
2. Pay attention to the USB cable. The speed of the USB cable is higher during the upgrade process. You need to choose a better quality USB cable to avoid poor contact.
3. You need to run the upgrade tool with administrator privileges (SIM7500_SIM7600_QDL V1.41 only for Update)
4. Uninstall and reinstall the upgrade tool (SIM7500_SIM7600_QDL V1.41 only for Update)
5. For more operation details, please refer to this video: https://www.waveshare.net/wiki/SIM7600-Firmware-upgrade-Video
If the short message is stored in the SIM card, usually 50 is the upper limit. You can use the command: AT+CPMS? Make a query
- Gain: 9dbi ± 0.7dbi
- It is recommended to use the more convenient RNDIS dial
- Can burn the latest Raspberry Pi Raspbian system, reconfigure NDIS dial-up
- Or use the image that has been configured with the driver NDIS dial-up and start the raspbian system image (the driver has been installed)
SIM7600 old driver
The general operation is: download the sample program, after decompression, rename the c folder under the Raspberry folder to SIM7600X, then copy the entire SIM7600X folder to the Raspberry Pi /home/pi directory, and enter the command line to /home/pi /SIM7600X directory, and then execute the chmod 777 sim7600_4G_hat_init command.