Difference between revisions of "RPi IR-CUT Camera"
From Waveshare Wiki
(Created page with "{{Infobox item|colorscheme=black |img=300px|alt=RPi IR-CUT Camera|link=http://www.waveshare.com/rpi-ir-cut-camera.htm|RPi IR-CUT Camera |c...") |
|||
(3 intermediate revisions by 2 users not shown) | |||
Line 2: | Line 2: | ||
|img=[[File:RPi-IR-CUT-Camera-intro.JPG|300px|alt=RPi IR-CUT Camera|link=http://www.waveshare.com/rpi-ir-cut-camera.htm|RPi IR-CUT Camera]] | |img=[[File:RPi-IR-CUT-Camera-intro.JPG|300px|alt=RPi IR-CUT Camera|link=http://www.waveshare.com/rpi-ir-cut-camera.htm|RPi IR-CUT Camera]] | ||
|caption= | |caption= | ||
− | |category= | + | |category= [[:Category:Cameras|Cameras]], [[:Category:Raspberry Pi|Raspberry Pi]], [[:Category:Raspberry Pi Camera|Raspberry Pi Camera]] |
|brand=Waveshare | |brand=Waveshare | ||
+ | |{{#urlget:amazon|default}}=display | ||
|website_cn=[http://www.waveshare.net/shop/RPi-IR-CUT-Camera.htm 网站] | |website_cn=[http://www.waveshare.net/shop/RPi-IR-CUT-Camera.htm 网站] | ||
|website_en= | |website_en= | ||
Line 15: | Line 16: | ||
*[http://www.waveshare.com/w/upload/6/61/RPi-Camera-User-Manual.pdf User manual] | *[http://www.waveshare.com/w/upload/6/61/RPi-Camera-User-Manual.pdf User manual] | ||
==FAQ== | ==FAQ== | ||
+ | {{FAQ| | ||
+ | How to toggle the working mode? | ||
+ | | | ||
+ | RPi IR-CUT Camera works on Normal Mode by default. There are two ways to toggle between Normal Mode and Night-vision Mode. | ||
+ | |||
+ | 1. By editing the config.txt file: | ||
+ | sudo nano /boot/config.txt | ||
+ | and append: | ||
+ | <nowiki>disable_camera_led=1</nowiki> | ||
+ | exit with save and restart your Pi then the camera will work on Night-vision Mode. | ||
+ | |||
+ | To revert to the Normal Mode, please remove the line <nowiki>disable_camera_led=1</nowiki> then save and restart your Pi. | ||
+ | |||
+ | 2. By changing the level on this position: | ||
+ | |||
+ | [[File:Rpi-ir-cut-camera-faq-4.jpg|400px]] | ||
+ | |||
+ | Thus, you can connect the GPIO from your Pi to this position, and toggle modes by changing the GPIO logic level. (HIGH --> Normal Mode, LOW --> Night-vision Mode) | ||
+ | }} | ||
==Support== | ==Support== | ||
{{Service00}} | {{Service00}} | ||
+ | |||
+ | [[Category:Cameras|Cameras]] [[Category:Raspberry Pi|Raspberry Pi]] [[Category:Raspberry Pi Camera|Raspberry Pi Camera]] |
Revision as of 10:07, 28 September 2017
| ||
Introduction
Resources
FAQ
Answer:
RPi IR-CUT Camera works on Normal Mode by default. There are two ways to toggle between Normal Mode and Night-vision Mode.
1. By editing the config.txt file:
sudo nano /boot/config.txt
and append:
disable_camera_led=1
exit with save and restart your Pi then the camera will work on Night-vision Mode.
To revert to the Normal Mode, please remove the line disable_camera_led=1 then save and restart your Pi.
2. By changing the level on this position:
Thus, you can connect the GPIO from your Pi to this position, and toggle modes by changing the GPIO logic level. (HIGH --> Normal Mode, LOW --> Night-vision Mode)
{{{5}}}
Support
Support
If you require technical support, please go to the Support page and open a ticket.