Difference between revisions of "Open407Z-C"
m (Text replace - ".htm More]" to ".htm More]}}") |
m (Text replace - " [http://www.waveshare.com/" to " {{Amazon|default=display |More = [http://www.waveshare.com/") |
||
Line 41: | Line 41: | ||
STM32 development board designed for the STM32F407ZxT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions. | STM32 development board designed for the STM32F407ZxT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions. | ||
− | [http://www.waveshare.com/Open407Z-C-Standard.htm More]}} | + | {{Amazon|{{#urlget:amazon|default}}=display |
+ | |More = [http://www.waveshare.com/Open407Z-C-Standard.htm More]}} | ||
{{Open407Z-C User Manual}} | {{Open407Z-C User Manual}} | ||
== Resources == | == Resources == |
Revision as of 06:21, 3 November 2016
[中文]
Introduction
STM32 development board designed for the STM32F407ZxT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions.
More |
Open407Z-C Testing Guide
Basic settings of the experiment
- Programming Interface: SWD
- Serialport settings: Select a proper COM port, configure as follows:
- Baud rate:115200;
- Data bits:8;
- Stop bits:1;
- Parity bits:None;
- Flow control:None
- Power supply: 5V power supply is required.
- Hardware Connection: For the tests that require the serial portconverter for debugging, please connect the converter to the board via pinheaders, and then connect it to PC by USB cable.
ADC+DMA
Overview
ADCanalog voltage acquisition
Hardware Connection
- Connect the serial port converter to theboard via USART2 interface.
- Connect the Analog Test Board to theboard via SPI1 interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant as adjusting the resistoron the module.
CAN1TO CAN2-Normal
Overview
CAN1TO CAN2-Normal demo
Hardware Connection
- Connectthe serial port converter to the board via USART3.
- Two "SN65HVD230 CAN Board" arerequired for this test.
- Connect the two "CAN Board" tothe board via CAN1, CAN2 interface respectively.
- Connect the two "CAN Board" by jumper wires(CANH <-> CANH, CANL <-> CANL).
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Pressthe USER key and check the results on the serial debugging assistant.
DAC
Overview
DACoutput demo
Hardware Connection
- Connect the Analog Test Board to theboard via SPI1 interface
- Connect the 5V pin headers on both themain board and the Analog Test Board via jumper wire.
Asshown in the figure below:
Operation and Result
You should hear the sound of the triangular wave from the AnalogTest Board.
DCMI_OV7670
Overview
Digitalcamera OV7670 demo
Hardware Connection
- Connect the OV7670 Camera Board to theboard via DCMI interface.
- Connect the 3.2inch 320x240 Touch LCD (C) to the board via LCD interface.
Asshown in the figure below:
Operation and Result
Imagesacquired from the camera will be displayed on the LCD.
DCMI_OV9655
Overview
Digitalcamera OV9655 demo
Hardware Connection
- Connect the OV9655 Camera Board to theboard via DCMI interface.
- Connect the 3.2inch 320x240 Touch LCD(A) to the board via LCD interface.
Asshown in figure below:
Operation and Result
Imagesacquired from the camera will be displayed on the LCD.
DS18B20+
Overview
DS18B20 temperature measurement demo
Hardware Connection
- Insert the DS18B20+ to the ONEWIRE Interface.
- Connect the serial port converter to theboard via USART3.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Checktemperature measurement results on the serial debugging assistant.
GPIO_Key_LED
Overview
LED,Pushbutton and Joystick demo
Hardware Connection
- Short the 4 LED jumpers on the board.
- Short the push button and joystick jumpers on the board.(2 for KEY JMP and 5 for JOYSTICK JMP)
Asshown in the figure below:
Operation and Result
Press the key or joystick; the LED status shouldkeep changing accordingly.
I2C
Overview
I2CEEPROM demo
Hardware Connection
- Connect the serial port converter to theboard via UART3 interface.
- Connect the AT24CXX EEPROM Board to theboard via I2Cx interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Check the test results of the I2C EEPROM on the serial debuggingassistant.
LCD-HY32D_FSMC
Overview
LCDdisplay demo
Hardware Connection
- Connect the 3.2inch 320x240 Touch LCD(A) to the board via LCD Interface. As shown in the figure below:
Operation and Result
Informationwill be displayed on the LCD
MCO_OUT
Overview
Clocksignal output demo
Operation and Result
Output8MHz external crystal signal on the MCO0 (PA8 pin)
Nand Flash_SCB0
Overview
NandFlash_SCB0 demo
Hardware Connection
- Connect the NandFlash Board (A)(K9F1G08U0D SCB0 onboard) to the board via 8BIT FSMC interface.
- Connect the serial port converter to theboard via USART3.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant.
NorFlash
Overview
NorFlashdemo
Hardware Connection
- Connect the NorFlash Board (A) to theboard via FSMC interface
- Connect the serial port converter to theboard via USART3
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant.
PS2
Overview
PS2keyboard demo
Hardware Connection
- Connect the PS2 keyboard to the boardvia PS2 interface.
- Connect the serial port converter to theboard via USART3 interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Pressany key on the keyboard, the corresponding key value will be displayed on the serialdebugging assistant.
RTC
Overview
RTCdemo
Hardware Connection
- Connect the serial port converter to theboard via USART3 interface. As shown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Followthe tips and input data, Info/message will be displayed on the serial debuggingassistant..
SD_FatFS
Overview
SDIOinterface + FatFS demo
Hardware Connection
- Connect the Micro SD Storage Board (withSD card) to the board via SDIO interface.
- Connect the serial port converter to theboard via USART3 interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant.
SDIO
Overview
SDIOinterface demo
Hardware Connection
- Connect the Micro SD Storage Board (withSD card) to the board via SDIO interface.
- Connect the serial port converter to theboard via USART3 interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the Serial debugging assistant.
SPI
Overview
SPIFlash demo
Hardware Connection
- Connectthe serial port converter to the board via USART3 interface.
- Connect the AT45DBXX DataFlash Board tothe board via SPIx interface.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant.
SRAM
Overview
SRAMdemo
Hardware Connection
- Connect the IS62WV12816BLL SRAM Board to the board viaFSMC interface.
- Connect the serial port converter to theboard via USART3 interface.
As shownin the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the serial debugging assistant.
TouchPanel
Overview
LCDtouch screen demo
Hardware Connection
- Connect the 3.2inch 320x240 Touch LCD (C) to the boardvia LCD interface.
Asshown in the figure below:
Operation and Result
LCDtouch screen function works, and allows writing and drawing on the LCD.
UcosII2.91+UCGUI3.90A
Overview
UcosII2.91+UCGUI3.90ADEMO
Hardware Connection
- Connect the LCD to the board via LCDconnector.
Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the uCOSView-V310G and LCD.
USARTx_pritf
Overview
USARTserial port demo
Hardware Connection
- Connect the serial port converter to theboard via USART3 interface.Asshown in the figure below:
Operation and Result
Launch the serial debugging assistant, and configure it asdescribed in chapter "Preparation".
Info/messagewill be displayed on the uCOSView-V310G and LCD.
VS1003BMP3 Board
Overview
VS1003BMP3 Board demo
Hardware Connection
- Connect the VS1003B MP3 Board to the board via SPI interface, as shown in the figure below:
Operation and Result
- Insert the headphone to the Line Out port.
- Connect the PC audio port and the VS1003BMP3 Board Line In port by audio cable.
- Play music on the PC side, then
- VS1003 (GPIO): P0 LED keeps blinking;
- VS1003 (line in): Music will be heard from PC;
- VS1003 (line out): Music will be heard from MCU FLASH;
- VS1003 (record): Sound can be heard from the Miconboard.
I2S
Overview
I2Sdemo
(1) MCU_FLASH
Hardware Connection
- Connect the UDA1380 Board to the board via I2S interface.Asshown in the figure below:
Operation and Result
Putthe headset to the HEADPHONE jack, then will hear the music stored in the MCUFLASH.
(2) SD_FatFS
Hardware Connection
- ·Connectthe UDA1380 Board to the board via I2S interface.
- Connect the Micro SD Storage Board (with SDCard) to the board via SDIO interface.
- Connect the serial port converter to theboard via USART3.
Asshown in the figure below:
Operation and Result
- Put the audio file named"Audio.wav" on SD card root directory.
•Put theheadset to the HEADPHONE jack. •SD cardaudio file information will be displayed on the serial debugging assistant. •Headsetwill output the music named Audio.wav on SD card root directory.
USBFS Example
Overview
USBFS demo
Hardware Connection
- Shortthe 3 jumpers PC2-FLG, PC1-PWROUT and PA9-VBUS for the following demo.
- Connect the 3.2inch 320x240 Touch LCD(A) to the board via LCD interface.
- Short the Joystick, LED jumpers.
Asshown in the figure below:
(1) USB_Device_Examples--HID
Hardware Connection
- Connect the PC and the Core board by USB Cable, as shownin the figure below:
Operation and Result
Message/info will be displayed on the LCD, andJOYSTICK can be used for simulating the mouse and controlling movement of thecomputer and mouse.
(2) USB_Device_Examples--MSC
Hardware Connection
- Connectthe PC and the Core board by USB Cable.
- Connect the Micro SD Storage Board (withSD card) to the board via SDIO interface, should open LEDs jumper
Asshown in the figure below:
Operation and Result
- Message/info will be displayed on the LCD and SD card hard disk will befounded in the PC.
(3) USB_Device_Examples--VCP
Hardware Connection
- Connectthe PC and the Core board by USB Cable. As shown in the figure below:
Operation and Result
Afterinstall the driver, the PC will detect the USB virtual COM port.
Asshown in the figure below:
(4) USB_Host_Examples--MSC
Hardware Connection
- Connect the Core board and the USBFlash Drive by the USB OTG cable. As shown in the figure below:
Operation and Result
Message/infowill be displayed on the LCD; the example code will place a TXT file into theUSB Flash Drive, list the files in the USB Flash Drive, and display thepicture.bmp.
(5) USB_Host_Examples--HID
Hardware Connection
- Connect the Coreboard and the USB mouse / keyboard by the USB OTG cable. As shownin the figure below:
Operation and Result
There will be information displayed on theLCD, and after follow the LCD tips, the mouse or keyboard will be identified:
- When identified as USB keyboard, the LCD will display the informationinput from the keyboard.
- When identified as USB mouse, the LCD will display the mouse currentstatus.
USBHS Example
Overview
USBHS Examples
Hardware Connection
- Open the 3jumpersPC2-FLG, PC1-PWROUT and PA9-VBUS for the following test.
- Connect the 3.2inch 320x240 Touch LCD(A) to the board via LCD interface.
- Short the Joystick, LED jumpers.
- Connect the USB3300 USB HS Board to theboard via ULPI interface.
Asshown in the figure below:
(1) USB_Device_Examples--DualCore
Hardware Connection
- Part 1: Connect the PC and USB3300 USB HS Board OTGreceptacle by USB cable, and then connect the Micro SD Storage Board (with SDcard) to the board via SDIO interface.
Asshown in the figure below:
- Part 2: Connect the core board (FS USB interface) and PCby USB cable; Short the 3 jumpers PC2-FLG, PC1-PWROUT, PA9-VBUS. As shownin the figure below:
Operation and Result
Part 1: Message/info will be displayed onthe LCD; SD card hard diskwill be founded in the PC.
- Part 2: Message/info will be displayed on the LCD, and JOYSTICK canbe used for simulating the mouse and controlling movement of the computer andmouse.
(2) USB_Device_Examples--HID
Hardware Connection
- Connect the PC and USB3300 USB HS Board OTG receptacle by USB cable. As shownin the figure below:
Operation and Result
- Message will be displayed on the LCD,control the computer cursor by joystick LCD.
(3) USB_Device_Examples--MSC
Hardware Connection
- Connect the PC and USB3300 USB HS Board OTG receptacle by USB cable, and connectthe Micro SD Storage Board (with SD card) to the onboard SDIO interface. As shownin the figure below:
Operation and Result
Messagewill be displayed on the LCD; SD card hard disk will be founded in the PC.
(4) USB_Device_Examples--VCP
Hardware Connection
- Connect the PC and USB3300 USB HS BoardOTG receptacle by USB cable. As shown in the figure below:
Operation and Result
Afterinstall related driver, the PC will detect the USB virtual COM port.
Asshown in the figure below:
(5) USB_Device_Examples--MSC
Hardware Connection
- Connect a USB flash drive to the USB3300USB HS Board HOST receptacle, as shown in the figure below:
Operation and Result
Message/infowill be displayed on the LCD; the example code will place a TXT file into theUSB Flash Drive, list the files in the USB Flash Drive, and display thepicture.bmp.
(6) USB_Host_Examples--DualCore
Hardware Connection
- Part 1: Connect a USB flash drive to the USB3300 USB HSBoard HOST receptacle.
Asshown in the figure below:
- Part 2: Connect a USB mouse or keyboard to the onboard FSUSB interface through a USB OTG cable, short 3 jumpers PC2-FLG, PC1-PWROUT, PA9-VBUS.
Asshown in the figure below:
Operation and Result
- Part 1: The LCD will display the file list in the USBflash drive, the example code will place a TXT file into the USB flash drive,and then the LCD will display the picture.bmp.
- Part 2: When identified as USBkeyboard, the LCD will display the information input from the keyboard.
When identifiedas USB mouse, the LCD will display the mouse current status.
(7) USB_Device_Examples--HID
Hardware Connection
- Connect a USBKeyboard or USB mouse to the USB3300 USB HS Board HOST receptacle.
Asshown in the figure below:
Operation and Result
The mouse or keyboard will be identified:
- When identified as USB keyboard, the LCD will display the informationinput from the keyboard.
. When identified as USB mouse, the LCDwill display the mouse current status.
(8) USB_Host_Device_Examples--DRD
Hardware Connection
Part1:
- Connect the Micro SD Storage Board (withSD card) to the onboard SDIO interface.
- Connect the USB3300 USB HS Board FS USB interface andPC USB port by USB cable.
Asshown in the figure below:
Part2:
- Connect a USB mouse or keyboard to theonboard USB interface through an USB OTG cable.
Asshown in the figure below:
Operation and Result
Part1:
Whenrunning DEVICE DEMO, you should find the SD card appears as a USB Flash Driveon the PC.
Part2:
The mouse or keyboard will be detected:
- When identified as USB keyboard, the LCDwill display the information input from the keyboard.
. When identified as USB mouse, the LCDwill display the mouse current status.
ETH
Overview
Ethernetdemo
PC IP Setting
Configurethe local connection of PC as follows:
IPadd: 192.168.1.11
NETMASK_ADDR:255.255.255.0
GW_ADDR:192.168.1.1
Hardware Connection
- Connect the DP83848 Ethernet Board to theonboard ETH interface, then connect it to the PC through a straight-through Ethernetcable.
- Connect the "3.2inch 320x240 TouchLCD" to the board via LCD interface.
Asshown in the figure below:
(1)STM32F4x7_ETH_LwIP_V1.0.0—Standalone--httpserver
Operation and Result
Enter192.168.1.10 on the Internet Explorer; you'll see the demo page.
(2)STM32F4x7_ETH_LwIP_V1.0.0—Standalone—tftpserver
Operation and Result
Referto "Open407Z\ETH\STM32F4x7_ETH_LwIP_V1.0.0\LwIP TCPIP stack demonstrationfor STM32F407 microcontrollers.pdf" for more details.
Youcan find the related software in Open407Z\ETH\Tool.
(3)STM32F4x7_ETH_LwIP_V1.0.0—FreeRTOS--httpserver_netconn
Operation and Result
Enter192.168.1.10 on the Internet Explorer; you'll see the demo page.
(4)STM32F4x7_ETH_LwIP_V1.0.0—FreeRTOS--httpserver_socket
Operation and Result
Enter192.168.1.10 on the Internet Explorer; you'll see the demo page.
Resources
STM32 Software
IDE
Programmers
USB Driver
Other Software
STM32F4 Datasheets
- STM32F405_STM32F407-Datasheet.pdf
- STM32F427_STM32F429-Datasheet.pdf
- STM32F437_STM32F439-Datasheet.pdf
- STM32F4-Reference.pdf
- REDIRECT Template:Related Resources
Support
Support
If you require technical support, please go to the Support page and open a ticket.