Open32F3-D
[中文]
Getting Started with modules
We provide various modules for Open32F3-D development board aiming to improve your development efficiency. These modules are not only designed for STM32 but also can be used for many other MCU platforms. Let's begin with the demos.
Development Environment
- KEIL MDK Version: 4.54 or above
- Programmer/Debugger: STM32F3-discovery onboard ST-LINK/V2
- Programming/Debugging interface: JTAG/SWD
- Serial port communication settings:
Select a proper COM port | |
---|---|
Baud rate | 115200 |
Data bits | 8 |
Stop bits | 1 |
Parity bits | None |
Flow control | None |
8BitIO-Pushbutton
Overview
8I/Os demo, detect the 8 independent button is pressed or not
Hardware connection
|
Operation and result
The below information will be displayed on the serial debugging assistant:
ADC
Overview
AD acquisition demo
Hardware connection
|
Operation and result
- Rotate the onboard potentiometer, the AD message will be printedon the serial debugging assistant:
CAN-LoopBack
Overview
Internal CANsignal demo
Hardware connection
Operation and result
- 4 LEDs bright at the beginning, the two middle LEDs bright after awhile
CAN-Normal
Overview
CANcommunication between two boards
Hardware connection
|
Operation and result
- The below information will be displayed on the serial debugging assistant:
DAC_SignalsGeneration
Overview
DA output demo,output via DMA channel
Hardware connection
|
Operation and result
- You will hear sound from the Analog Test Board.
FATFSV0.08A-SD Card
Overview
Read and write SD card; SD card is FAT file system
Hardware connection
Insert the SD card to the Micro SD Storage Board socket
|
Operation and result
The below information willbe displayed on the serial debugging assistant:
FreeRTOS7.3.0
Overview
Build two LED tasks based on Free RTOS real-time operation system; switching the two tasks
Hardware connection
Operation and result
LED blinking;
GPIO_LED_KEY
Overview
Control the LED via button
Hardware connection
|
Operation and result
The LED status will changeaccordingly while press the JOYSTICK or the button.
HS1101LF
Overview
HS1101LF sensor demo
Hardware connection
|
Operation and result
The humidityvalue will be printed on the serial debugging assistant:
I2C
Overview
Read and write data on E2PROM via I2C protocol
Hardware connection
|
Operation and result
- The below information will be displayed on the serial debugging assistant:
I2S UDA1380 &SD_FatFS(DMA)
Overview
Drive the UDA1380 Board toplay music by using Fillips I2S protocol.
Hardware connection
|
Operation and result
You will hear music while pressing the RESET key.
LCD
Overview
Control the LCDvia FSMC
Hardware connection
|
Operation and result
- The below information will displayed on the LCD:
LDR
Overview
Humidity sensor demo
Hardware connection
|
Operation and result
The humidity value will be printed on the serial debugging assistant:
NRF24L01
Overview
NRF24L01 transmits datavia wireless way
Hardware connection
|
Software connection
Two NRF24L01 is needed for this demo, software configuring as below:
When configuring as mode of transmitting, enabled: #define T_O_R 1, comment out: //#define T_O_R 0
When configuring as mode of receiving, enable: #define T_O_R 0,comment out: //#define T_O_R 0
Operation and result
Message will be printed on theserial debugging assistant.
One-Wire
Overview
Connect the DS18B20,detect the temperature
Hardware connection
Connect the DS18B20 board to the board via One-Wire interface.
Operation and result
The below information will be displayed on the serial debugging assistant:
PS2
Overview
Drive PS2 keyboard via 2GPIO
Hardware connection
|
Operation and result
While pressing keys on thePS2 keyboard, related key value will be displayed on the serial debugging assistant:
SPI
Overview
SPI interface drives the AT45DBXXDataFlash Board
Hardware connection
|
Operation and result
The belowinformation will be printed on the serial debugging assistant:
Touch Panel
Overview
Control the LCD via FSMC, display the touch function of the LCD
Hardware connection
|
Operation and result
Calibrate the LCD first,then touch it, draw any line on it.
uCOS-II-V2.91
Overview
Build two LED tasks based on uCOSII; switching the two tasks
Hardware connection
Operation and result
Two LED blinking
uCOSII2.91+UCGUI3.90A
Overview
UcosII+GUI demo
Hardware connection
|
|
Operation and result
- Below information will displayed on the LCD:
USART
Overview
USART serial port communication demo
Hardware connection
Connect theRS232 board to the board via USART1 interface( Connect to USART2 or USART1 depends on the program)
Operation and result
The below information will be printed on the serial debugging assistant:
ZIGBEE
Overview
Drive AT45DBXX Data Flash Board via SPI interface
Hardware connection
|
Operation and result
The below information will be printed on the serial debugging assistant:
VS1003B
Overview
Play music via VS1003B module
Hardware connection
|
Operation and result
- Connect VS1003Bto the PC via Line in interface, connect the earphone to VS1003B via Line out interface, you will hear music from the computer.
- Connect the earphone toVS1003B via Line out interface; you will hear music from MCU FLASH.
Resources
STM32 Software
IDE
Programmers
USB Driver
Other Software
STM32F3 Datasheets
- REDIRECT Template:Related Resources
Support
Support
If you require technical support, please go to the Support page and open a ticket.