LC76G GNSS Module

LC76G

L76K

{{{name3}}} GNSS UART/I2C

{{{name4}}}

{{{name5}}}

Primary Attribute Category: {{{userDefinedInfo}}}: {{{userdefinedvalue}}} Brand: Waveshare

Website International: Website Chinese: 官网

Onboard Interfaces

Related Products

Overview

The LC76G GPS Module is a Multi-GNSS (Global Navigation Satellite System) module, supports GPS, BeiDou (BDS), GLONASS, Galileo, and QZSS systems, allows multi-system combined or single-system independent positioning. Supports EPO™ (Extended Predictive Orbit) and EASY™ (Embedded Assist System) function, provides a good positioning experience of fast, accurate, high-performance.
This module provides control demos for Raspberry Pi, Arduino, Raspberry Pi Pico and ESP32.

Parameters

Model	LC76G(AB)	L76K	L76B
Compatible
Picture
GNSS	GPS/GLONASS/Galileo/BDS/QZSS	GPS/GLONASS/BDS/QZSS	GPS/BDS/QZSS
Form Factor	LCC	LCC	LCC
Dimensions	9.7×10.1×2.4	9.7×10.1×2.4	9.7×10.1×2.4
Weight (g)	0.6	0.4	0.5
Normal Operating Temperature	-40℃ ~+85℃	-40℃ ~+85℃	-40℃ ~+85℃
Storage Temperature	-40℃ ~+90℃	-40℃ ~+90℃	-40℃ ~+90℃
Main Feature
Function	Standard	Standard	Example
Chip	AG3352Q	AT6558R	MT333
L1 Receiver (Channel)	47 tracking ch	32 tracking ch/72 acquisition ch	22 tracking ch/66 acquisition ch
L1 Receiver SBAS	Support	N/A	Support
A-GNSS	Support	Support	Support
Sensitivity (Auto-aquisition)	-147dBm	-148dBm	-148dBm
Sensitivity (re-acquisition)	-159dBm	-160dBm	-160dBm
Sensitivity (tracking)	-166dBm	-162dBm	-163dBm
TTFF (Time To First Fix) Cold Starts	26s, Autonomous 12s, with EASY™ 5s,with EPO™	30s, Autonomous 5.5s, With AGNSS	35s, Autonomous 15s, with EASY™
TTFF (Time To First Fix) Warm Starts	20s, Autonomous 2s, with EASY™	/	30s, Autonomous 5s, with EASY™
TTFF (Time To First Fix) Hot Starts	1s	2s	1s
Position Accuracy	1.5m CEP	2.0m CEP	2.5m CEP
Velocity Accuracy	0.1m/s	0.1m/s	0.1m/s
Acceleration Accuracy (Max)	0.1m/s²	0.1m/s²	0.1m/s²
Timing Accuracy	100ns	30ns	10ns
Update Rate (Max)	10Hz	5Hz	10Hz
Default Baudrate	115200bps	9600bps	9600bps
Geo-fence	⚪	/	⚪
Interference Detection	⚪	/	⚪
Anti-jamming	⚪	/	⚪
LNA	⚪	⚪	⚪
Electrical Parameters
Power Supply	2.55to3.6V	2.7Vto3.4V	2.8Vto4.3V
Power Consumption (Acquisition)	36mA(G3B)	29mA (GPS+BDS)	29mA (GPS+BDS)
Power Consumption (Tracking)	36mA(G3B)	29mA (GPS+BDS)	18mA (GPS+BDS)
Power Consumption (RTC backup/low power consumption	13μA	8μA	7μA
Interface
UART	⚪	⚪	⚪
IIC (NMEA)	⚪	/	⚪
Reset	⚪	⚪	⚪
Timing Pulse	⚪	⚪	⚪
Antenna
Short circuit and open circuit detection	⚪	⚪	⚪
Antenna Type	Active, Passive	Active, Passive	Active, Passive
Antenna Power Supply	External or Internal	External or Internal	External or Internal

Interface

Interface	Description
VCC	Power supply (3.3V~5V)
GND	Ground
TX	UART data output
RX	UART command input
PPS	GPS status indicator
RST	Reset pin
SDA	I2C data pin
SCL	I2C clock pin

NMEA0183

• The host control output NMEA0183 information from the serial port and analyzes NMEA 0183 sentence to output the information.
• NMEA 0183 is a standard format developed by the National Marine Electronics Association for marine electronic equipment. It has now become a unified RTCM (Radio Technical Commission for Maritime Services) standard protocol for GPS navigation equipment.
• NMEA 0183 includes 7 protocol frames including $GPZDA, $GPRMC, $GPVTG, $GPGNS, $GPGGA, $GPGSA, $GPGSV*3, $GPGLL, $GPGST, among which the first two characters followed by $ represent the country or region. For example, GPGGA stands for American GPS, BDGGA stands for China Beidou, GLGGA stands for Russia GLONASS, GAGGA stands for EU Galileo, and GNGGA stands for multi-satellite joint positioning.
• Take $GPRMC as an example to briefly describe the information represented by each part of the protocol frame. Please refer to the NMEA 0183 manual for the other 6 protocol frames.

Recommended Minimum Specific GPS/TRANSIT Data (RMC) recommended positioning information
$GPRMC,<1>,<2>,<3>,<4>,<5>,<6>,<7>,<8>,<9>,<10>,<11>,<12> *hh<CR><LF>
$GNRMC,010555.000,A,2232.4682,N,11404.6748,E,0.00,125.29,230822,,,D*71
<1> UTC time, hhmmss.sss (hour, minute, second) format
<2> Positioning state, A=valid positioning, V=invalid positioning
<3> Latitude ddmm.mmmm (degrees and minutes) format (the front 0 will also be transmitted)
<4> Latitude hemisphere N (Northern Hemisphere) or S (Southern Hemisphere)
<5> Longitude dddmm.mmmm (degrees and minutes) format (the preceding 0 will also be transmitted)
<6> Longitude hemisphere E (East longitude) or W (West longitude)
<7> Ground speed (000.0~999.9 knots, the preceding 0 will also be transmitted)
<8> Ground heading (000.0~359.9 degrees, with true north as the reference, the preceding 0 will also be transmitted)
<9> UTC date, ddmmyy (day month year) format
<10> Magnetic declination (000.0~180.0 degrees, the previous 0 will also be transmitted)
<11> Magnetic declination direction, E (East) or W (West)
<12> Mode indication (only NMEA0183 version 3.00 output, A=autonomous positioning, D=difference, E=estimation, N=data invalid)
*hh: The last check code *hh is the data used for parity. In normal use, it is not necessary, but when there is strong electromagnetic interference in the surrounding environment, it is recommended to use. hh represents the bitwise XOR value of all characters of "$" and "*" (excluding these two characters). Individual manufacturers define their own statement format starting with "$P", followed by a 3-character manufacturer ID number, followed by a custom data body.

PAIR Sentence

This chapter describes common PAIR messages (proprietary NMEA messages defined by the chipset vendor). "P" for proprietary messages and "AIR" for chipset vendor-defined commands.

Sentence	Description	Example	Function
$PAIR864,<PortType>,<PortIndex>,<Baudrate>*<Checksum>	Configure NMEA UART baudrate	$PAIR864,0,0,115200*1B $PAIR864,0,0,9600*13	Set the baudrate as 115200/9600 <CMD>Support the following baudrate 9600 115200(default) 230400 460800 921600 3000000
$PAIR050,*<Checksum>	Set the positioning frequency	$PAIR050,1000*12	Set the positioning frequency as 1Hz <Interval>Positioning interval: 100–1000, (Default:1000) (If the set frequency is greater than 1 Hz, only RMC and GGA are output at the set frequency, and the output of other NMEA sentences is kept at 1 Hz.)
$PAIR062,<Type>,<OutputRate>*<Checksum>	Configure NMEA statement output type and output frequency	$PAIR062,0,3*3D	Set the output frequency of GGAT statement in NMEA output to once every 3 positions （refer to Quectel_LC26G&LC76G&LC86G_GNSS_Protocol_Specification_V1.0.0_Preliminary, 2.3.13
$PAIR066,<GPS_Enabled>,<GLONASS_Enabled>,<Galileo_Enabled>,<BDS_Enabled>,<QZSS_Enabled>,0*<Checksum>	Configuring galaxies	$PAIR066,1,1,1,1,0,0*3A	Configuring galaxies as GPS+GLONASS+Galileo+BDS <*_Enabled>GNSS galaxies configuring 0 = Disable 1 = Enable (Configure GNSS galaxy mode by modifying each enabled bit.)
$PAIR004*<Checksum>	Hot starts	$PAIR004*3E	Hot starts
$PAIR005*<Checksum>	Warn starts	$PAIR005*3F	Warm starts
$PAIR006*<Checksum>	Cold starts	$PAIR006*3C	Cold starts
$PAIR007*<Checksum>	Clear system configuration and cold starts	$PAIR007*3D	Clear system configuration and cold starts

Note: After changing the configuration content, you need to modify the checksum <Checksum> accordingly. For more details, you can refer to LC76G chip GNSS protocol.

Working with Windows

• Connect the GPS antenna and the USB to the UART module (not included), and then connect to the computer as the picture shows. After connecting, the power indicator light (PWR) is always on.

Note: the red cable is not VCC and the black cable is not GND.

Module	USB to UART
VCC	5V/3.3V
GND	GND
RX	TXD
TX	RXD
PPS	NC

• Open the computer serial port debugging assistant, set the corresponding serial port number (com5 here), baud rate 9600, 8 data bits, 1 stop bit, no parity bit, and no flow control.

Sscom can be downloaded Here.

Note:
1. Due to the instability of GPS indoor search, please put the module or antenna next to the balcony or window, or conduct experiments directly outdoors.
2. The first positioning of the module (cold start), under normal circumstances (outdoors, good weather, no large building block), takes 35 seconds to successfully locate, please wait patiently. If the weather conditions are bad, it may take longer to locate, or even fail to locate.
Download U-center, unzip it, and open it for installation. Run the program, click the Receiver menu, select Port, and set the actual serial port number, Baudrate: 9600. Click (connect button) to connect to the GPS module, and the u-center will display various information, as shown below:

Working With Raspberry Pi

Provide C and Python demos for control in Raspberry Pi.

Enable UART Port (Skip if enabled)

Enable the Raspberry Pi terminal and input the following commands to enter the interface.

sudo raspi-config

Choose Interfacing Options -> Serial, close the shell visit, and enable the serial port of the hardware:

Hardware Connection

Module	Raspberry Pi
VCC	5V
GND	GND
TX	P15
RX	P14
PPS	NC

Minicom Debug

Download and install minicom tool:

sudo apt-get install minicom

The corresponding serial port number for the position hardware serial port:

ls -l /dev/serial*

If the system has used the serial port and has been modified, there are two scenarios:
The default state after enabling the UART function:

The state after modifying the UART config.

Need to find the serial port number corresponding to serial0 (that is, the serial port on GPIO), as shown in Figure 1, the serial port number is ttyS0, and Figure 2 is ttyAMA0; use minicom to open the serial port:

sudo minicom -D /dev/ttyS0 -b 9600

-D stands for port. If the serial port number in the previous step is ttyAMA0, then it is:

sudo minicom -D /dev/ttyAMA0 -b 9600

The default baud rate of minicom is 115200, if you need to set the baud rate to 9600, add the parameter -b 9600.

Exit: Ctrl+A then press X alone, YES to enter.

Download and Run the Test Demo

cd
sudo apt-get install unzip -y
sudo wget https://files.waveshare.com/upload/d/dc/LC76G_GPS_Module_code.zip
sudo unzip LC76G_GPS_Module_code.zip -d ./LC76G_GPS_Module_code
sudo chmod 777 -R ./LC76G_GPS_Module_code
cd ./LC76G_GPS_Module_code

Or click here to download, and then unzip it to Raspberry Pi.

Environment Debugging

Install the related function library of the demo.

BCM2835

#Open the Raspberry Pi terminal and run the following commands: 
wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.71.tar.gz
tar zxvf bcm2835-1.71.tar.gz 
cd bcm2835-1.71/
sudo ./configure && sudo make && sudo make check && sudo make install
# For more details, you can refer to: http://www.airspayce.com/mikem/bcm2835/

WiringPi

Open he Raspberry Pi terminal and run the following commands:

cd
sudo apt-get install wiringpi
#For Raspberry Pi systems after May 2019 (earlier than that may be implemented without), an upgrade may be required to:
wget https://project-downloads.drogon.net/wiringpi-latest.deb
sudo dpkg -i wiringpi-latest.deb
gpio -v
# Run gpio -v and version 2.52 will appear, if it does not appear, it means there is an installation error

#The Bullseye branch system uses the following command:
git clone https://github.com/WiringPi/WiringPi
cd WiringPi
./build
gpio -v
# Run gpio -v and version 2.70 will appear, if it does not appear it means there is an installation error

Python

The latest Raspberry Pi system needs to install a GPS data analysis library for running Python.

cd L76K_GPS_Module_code/RaspberryPi/python3/micropyGPS-master
sudo python setup.py install
#Wait for library installation

If the old system only supports Python2, it requires the function library.

sudo apt-get update
sudo pip install RPi.GPIO
sudo apt-get install python-serial

C Demo

cd C
make clean
make
sudo ./main

Baudu Coordinates are the coordinates converted from the Baidu map coordinates. Copy the coordinates to http://www.gpsspg.com/maps.htm, choose the Baidu map on the left side, and then you can see your location. (if you go directly to "Baidu Pickup Coordinate System" you need to Swap the positions of the two latitude and longitude numbers).

Python 3 Demo

cd python
sudo python main.py

Expected Result
It takes about 35 seconds for the module to be positioned for the first time.
The front is the raw data output by the module.
"Time" is the time output by L76X GPS Module.
Latitude and longitude are the output latitude and longitude and latitude and longitude direction.
Baidu Coordinates is the converted Baidu nao coordinates, copy the coordinates to http://www.gpsspg.com/maps.htm, select Baidu map on the left, and you can see your location (if you go directly to "Baidu Pickup Coordinate System" you need to "Swap" the positions of the two latitude and longitude numbers).

Python 2 Demo

cd python
sudo python main.py

Expected Result
It takes 35 seconds for the module to be positioned for the first time.
The front is the raw data output by the module.
Time is the time output by L76X GPS Module.
Latitude and longitude are the output latitude and longitude and the directions of latitude and longitude.
Baidu Coordinates is the converted Baidu map coordinates, copy the coordinates to http://www.gpsspg.com/maps.htm, select Baidu map on the left, and you can see your location (if you go directly to "Baidu Pickup Coordinate System" you need Swap the positions of the two latitude and longitude numbers).

Working with Arduino

This demo has been verified on Arduino MEGA2560.
Click to download the sample demo or download it in the #Resource.

Hardware Connection

Module	Arduino
VCC	5V
GND	GND
TX	RX2
RX	TX2
PPS	NC

Demo Use

Choose the Arduino mega2560 development board and the corresponding port, and upload the demo after verification.
The first position for the module will take 35 seconds.
Open SSCOM and set the baud rate as 9600.
The original data is output by the module at first.
Time is the time of L76X GPS Module output.
Lat and Lon are the output latitude and longitude and latitude and longitude directions. B_Lat and B_Lon are the converted Baidu map coordinates, copy the coordinates to http://api.map.baidu.com/lbsapi/getpoint/, and you can see your location (the coordinate format is longitude Lat first, latitude Lon after, separated by commas in the middle).

The file also comes with the Arduino uno demo, but the platform data accuracy is not enough, only to achieve the display of satellite data in time, want to other information can modify their own procedures.

Working with Raspberry Pi Pico

Hardware Connection

Module	Raspberry Pi Pico
VCC	5V
GND	GND
TX	GP1
RX	GP0
PPS	NC

Environment Building

We test the demo with Thonny in this tutorial, click to download the related IDE and open Thonny.

• Please refer to the official document to set up the Python environment. Choose a Raspberry Pi Pico device in Tools->Options->Interprete. As shown below:

Download Demo

1. Click to download demo.
2. Unzip the sample demo;
3. Open Thonny, first confirm that you have connected to Pico, then open the unzipped program path in the upper left corner, right-click on the Pico folder, and select Upload, as shown in the picture.

Demo Usage

1. Open Thonny IDE, choose the Pico directory, double-click to open the coordinate_convert.py file and run the demo, as shown below:

2. Under clear weather conditions, the LC76G will get the position about 30 seconds after powering up, as shown in the following figure when running the program:

3. Users can copy the location information displayed in the terminal of Thonny and use Google Map and Baidu Map to mark the coordinates.

ESP32

Hardware Connection

Module	ESP32
VCC	5V
GND	GND
TX	P16
RX	P17
PPS	NC

Environment Building

Install ESP32 plug-in On Arduino IDE

1. Open the Arduino IDE, click on the file in the upper left corner, and select Preferences.

2. Add the following link in the additional development board manager URL, then click OK.

https://dl.espressif.com/dl/package_esp32_index.json

Note: If you already have the ESP8266 board URL, you can separate the URLs with commas like this:

https://dl.espressif.com/dl/package_esp32_index.json，http://arduino.esp8266.com/stable/package_esp8266com_index.json

3. Download the package and copy the packages file to the following path:

C:\Users\xutong\AppData\Local\Arduino15

Note: Replace the username: xutong with your own username.

How To Use the Demo

• Download the demo and unzip it, and use the configured Arduino IDE to open the L76X.ino file in the ESP32 directory, and wait for all the files to be loaded.
• Use the data cable to connect the esp32 development board to the computer, and select the correct development board model and port number.
• Here we take the ESP32-S chip development board as an example: click in turn: Tools -> Development Board -> esp32 -> ESP32 Dev Module, and select the corresponding port number.
• Click "Verify" in the upper left corner, wait for the verification to complete without error, and then click "Upload".
• After the upload is complete, the demo runs automatically. Click Tools -> Serial Monitor in turn, and you can observe the running effect of the demo in the serial monitor window:

It takes 35 seconds for the module to be positioned for the first time. (It may be longer if the signal condition is not good). The front is the raw data output by the module. Time is the time output by L76X GPS Module. "Lat" and "Lon" are the output latitude and longitude and the directions of latitude and longitude.
B_Lat and B_Lon are the converted Baidu map coordinates, copy the coordinates to http://api.map.baidu.com/lbsapi/getpoint/, and you can see your location (the coordinate format is longitude Lat first, latitude Lon after, separated by commas in the middle).

Working with Jetson Nano

This demo has been burned in the Jetson Nano Dev Kit and verified.

Hardware Connection

Module	JETSON-NANO-DEV-KIT
VCC	5V
GND	GND
TX	10
RX	8
PPS	NC

Environment Debugging

Install pip Tool

Use apt-get tool to install python tool pip:

sudo apt-get install python3-pip   #python3
#After that, you need to enter the user password to verify

sudo apt-get install python2-pip   #python2
#After that, you need to enter the user password to verify

Wait for the installation.

Install Python Library

#Libraries required for python3 programs:
sudo pip3 install pyserial     #Serial Control Library
sudo pip3 install settools     #Install tools
cd jetson/python3/micropyGPS-master
sudo python3 setup.py install  #Data Analysis Library

Libraries needed for #python2 programs:
sudo pip install pyserial #serial port control library

Demo Use

Enter the directory and run main.py:

cd jetson/python3
sudo python3 main.py

It takes 35 seconds for the module to be positioned for the first time.

The front is the raw data output by the module.

Time is the time output by L76X GPS Module.

Latitude and longitude are the output latitude and longitude and the direction of latitude and longitude.

Baidu Coordinates is the converted Baidu map coordinates, copy the coordinates to http://www.gpsspg.com/maps.htm, select Baidu map on the left, and you can see your location (if you go directly to "Baidu Pickup Coordinate System" you need Swap the positions of the two latitude and longitude numbers).

Resource

Document

• L76X GPS Module Schematic
• 3D Drawing

Demo

• Sample demo

Software

• Sscom
• U-centersetup v8.12
• TCP232
• Chiness_Unicode
• Serial Bluetooth Terminal
• Thonny

Datasheet

• LC76G chip GNSS protocol specification
• More resources

FAQ

Support

If you require technical support, please go to the Support page and open a ticket.