Difference between revisions of "Jetson nano case (B)"
From Waveshare Wiki
| Line 10: | Line 10: | ||
<big> | <big> | ||
;Before assembling, please check the number of components, make sure all of them are included. | ;Before assembling, please check the number of components, make sure all of them are included. | ||
| − | [[File:jetson-case-assemble-manual-12.png]] | + | [[File:jetson-case-assemble-manual-12.png|900px]] |
| − | ;buttons | + | ;buttons connection |
| − | [[File:jetson-case-assemble-manual-13.jpg]] | + | [[File:jetson-case-assemble-manual-13.jpg|900px]] |
;1. Take apart core board of Jetson nano developer Kit and assemble wireless-AC 8265 card, connect antennas. | ;1. Take apart core board of Jetson nano developer Kit and assemble wireless-AC 8265 card, connect antennas. | ||
| − | [[File:jetson-case-assemble-manual-1.png]] | + | [[File:jetson-case-assemble-manual-1.png|900px]] |
;2. Assemble Jetson Nano developer kit back. | ;2. Assemble Jetson Nano developer kit back. | ||
| − | [[File:jetson-case-assemble-manual-2.png]] | + | [[File:jetson-case-assemble-manual-2.png|900px]] |
;3. Mounting Jetson Nano to bottom box of Jetson Nano Case (B) | ;3. Mounting Jetson Nano to bottom box of Jetson Nano Case (B) | ||
| − | [[File:jetson-case-assemble-manual-3.png]] | + | [[File:jetson-case-assemble-manual-3.png|900px]] |
;4. Firstly, insert 40PIN adapter board to 40PIN GPIO of Jetson Nano, then fixing antenna to antenna holes. To fix antenna, we recommend to you add a gasket. <font color=red><big>Please turn the antenna tightly by spanner.</big></font> | ;4. Firstly, insert 40PIN adapter board to 40PIN GPIO of Jetson Nano, then fixing antenna to antenna holes. To fix antenna, we recommend to you add a gasket. <font color=red><big>Please turn the antenna tightly by spanner.</big></font> | ||
| − | [[File:jetson-case-assemble-manual-4.png]] | + | [[File:jetson-case-assemble-manual-4.png|900px]] |
;5. Insert jumper cap to Buttons pins, Take the pins which are close to Camera interface as the first one, you should insert the jumper to last pins. Connect FFC cable of camera to camera interface | ;5. Insert jumper cap to Buttons pins, Take the pins which are close to Camera interface as the first one, you should insert the jumper to last pins. Connect FFC cable of camera to camera interface | ||
| − | [[File:jetson-case-assemble-manual-5.png]] | + | [[File:jetson-case-assemble-manual-5.png|900px]] |
;6. Assemble Reset button, Component 6 is fixed on button, you should take it out first | ;6. Assemble Reset button, Component 6 is fixed on button, you should take it out first | ||
| − | [[File:jetson-case-assemble-manual-6.png]] | + | [[File:jetson-case-assemble-manual-6.png|900px]] |
;7. Insert wires of Reset button to buttons pins, insert it to the third pins. Assemble Fan to Heat sink | ;7. Insert wires of Reset button to buttons pins, insert it to the third pins. Assemble Fan to Heat sink | ||
| − | [[File:jetson-case-assemble-manual-7.png]] | + | [[File:jetson-case-assemble-manual-7.png|900px]] |
;8. Assemble Power buttons, insert it to the first pins. | ;8. Assemble Power buttons, insert it to the first pins. | ||
| − | [[File:jetson-case-assemble-manual-8.png]] | + | [[File:jetson-case-assemble-manual-8.png|900px]] |
;9. Screwing nylon standoffs to Camera. Note that you cannot change it with metal screws, with metal standoffs, camera will damaged because of shorted problem. | ;9. Screwing nylon standoffs to Camera. Note that you cannot change it with metal screws, with metal standoffs, camera will damaged because of shorted problem. | ||
| − | [[File:jetson-case-assemble-manual-10.png]] | + | [[File:jetson-case-assemble-manual-10.png|900px]] |
;10. Fixing camera to Camera holder by nylon screw nuts. Assmeble the case then connect FFC cable to camera | ;10. Fixing camera to Camera holder by nylon screw nuts. Assmeble the case then connect FFC cable to camera | ||
| − | [[File:jetson-case-assemble-manual-11.png]] | + | [[File:jetson-case-assemble-manual-11.png|900px]] |
;11. Finally, stick Anti-slip rubbers to bottom of case. Connect Antennas | ;11. Finally, stick Anti-slip rubbers to bottom of case. Connect Antennas | ||
</big> | </big> | ||
Revision as of 07:48, 13 August 2019
Jetson Nano Case (B) Assembly
Hardware requires
Except Jetson Nano case (B), you may need to buy some modules separately.
These porducts should be purchased separately,if you require.
Assembly
- Before assembling, please check the number of components, make sure all of them are included.
- buttons connection
- 1. Take apart core board of Jetson nano developer Kit and assemble wireless-AC 8265 card, connect antennas.
- 2. Assemble Jetson Nano developer kit back.
- 3. Mounting Jetson Nano to bottom box of Jetson Nano Case (B)
- 4. Firstly, insert 40PIN adapter board to 40PIN GPIO of Jetson Nano, then fixing antenna to antenna holes. To fix antenna, we recommend to you add a gasket. Please turn the antenna tightly by spanner.
- 5. Insert jumper cap to Buttons pins, Take the pins which are close to Camera interface as the first one, you should insert the jumper to last pins. Connect FFC cable of camera to camera interface
- 6. Assemble Reset button, Component 6 is fixed on button, you should take it out first
- 7. Insert wires of Reset button to buttons pins, insert it to the third pins. Assemble Fan to Heat sink
- 8. Assemble Power buttons, insert it to the first pins.
- 9. Screwing nylon standoffs to Camera. Note that you cannot change it with metal screws, with metal standoffs, camera will damaged because of shorted problem.
- 10. Fixing camera to Camera holder by nylon screw nuts. Assmeble the case then connect FFC cable to camera
- 11. Finally, stick Anti-slip rubbers to bottom of case. Connect Antennas