Difference between revisions of "Compute Module 4 POE Board"

From Waveshare Wiki
Jump to: navigation, search
(Created page with "<div class="tabber"> <div class="tabbertab" title="Introduction"> {{infobox item| |name=Compute Module PoE Board |img=File:Compute-Module-4-POE-Board-1.jpg|400px|alt=Compute...")
 
 
(3 intermediate revisions by 2 users not shown)
Line 3: Line 3:
 
{{infobox item|
 
{{infobox item|
 
|name=Compute Module PoE Board
 
|name=Compute Module PoE Board
|img=[[File:Compute-Module-4-POE-Board-1.jpg|400px|alt=Compute Module PoE Board|link=https://www.waveshare.com/compute-module-4-poe-board.htm]]
+
|img=<div class="tabber"><div class="tabbertab" title="Compute Module 4 PoE Board">[[File:Compute-Module-4-POE-Board-1.jpg|400px|alt=Compute Module PoE Board|link=https://www.waveshare.com/compute-module-4-poe-board.htm]]</div><div class="tabbertab" title="Compute Module 4 Acce C/D">[[File:Compute-Module-4-Acce-D-1.jpg|400px|alt=Compute Module Acce D|link=https://www.waveshare.com/compute-module-4-acce-cd.htm]]</div>
 
|caption=Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4 / CM4L  
 
|caption=Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4 / CM4L  
 
|category=[[:Category:Raspberry Pi|Raspberry Pi]]
 
|category=[[:Category:Raspberry Pi|Raspberry Pi]]
Line 81: Line 81:
 
*[https://datasheets.raspberrypi.org/cm4io/cm4io-product-brief.pdf Raspberry Pi Compute Module 4 IO Board Brief]
 
*[https://datasheets.raspberrypi.org/cm4io/cm4io-product-brief.pdf Raspberry Pi Compute Module 4 IO Board Brief]
 
*[https://datasheets.raspberrypi.org/cm4io/cm4io-datasheet.pdf Raspberry Pi Compute Module 4 IO Board Datasheet]
 
*[https://datasheets.raspberrypi.org/cm4io/cm4io-datasheet.pdf Raspberry Pi Compute Module 4 IO Board Datasheet]
 +
*[https://www.raspberrypi.org/documentation/hardware/computemodule/cmio-camera.md  CSI Camera Reference]
 +
*[https://www.raspberrypi.org/documentation/hardware/computemodule/cmio-display.md  DSI Display Reference]
  
 
===3D Drawing===
 
===3D Drawing===

Latest revision as of 07:23, 9 April 2021

Compute Module PoE Board
Compute Module PoE Board
Compute Module Acce D


Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4 / CM4L
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Primary Attribute
Category: Raspberry Pi
{{{userDefinedInfo}}}: {{{userdefinedvalue}}}
Brand: Waveshare
Website
International: Website
Chinese: 中文官网
Onboard Interfaces
Related Products

Overview

This is an IO board for evaluating the Raspberry Pi CM4 or being integrated into end products. the board feature PoE function, it can be used for all variants of CM4.

Dimension

Compute_Module 4 POE Board
Compute-Module-4-POE-Board-details-size.jpg
Compute_Module 4 核心板
Compute Module 4 IO Board 5.png

What's on board

Compute-Module-4-POE-Board-details-intro.jpg

No. Component Description
1 CM4 connector Suitable for all variants of Compute Module 4
2 DC power port 7~36V DC wide range power supply, recommend 24W power adpater at least.
3 Gigabit Ethernet RJ45 with PoE support 10/100M auto-negotiation, for connecting router or switch with PoE function
4 USB SLAVE Interface Writing emmc for Compute Module 4
5 USB3.2 Interface 4 x USB 3.2 Gen1 interface for USB devices.
6 HDMI Interface Dual HDMI ports for dual 4K 30fps output.
7 RTC RTC battery holder. The real-time clock can be used to wake up, shutdown or reboot Compute Module 4.
8 CAM 2x MIPI CSI camera connectors.
9 DISP 2x MIPI DSI display connectors.
10 FAN Fan header, support PWM Fan.
11 FAN Power Select 5V or 12V voltage to drive the fan
12 IO-VREF/PoE selection IO-VREF:CM4 IO logic level: 3.3V or 1.8V
PoE: enable (EN) or disable (DIS)
13 40PIN GPIO header For connecting Raspberry Pi HATs
14 CAM0 and DISP0 I2C bus fit the jumpers when using CAM0 or DISP0
15 Misc configurations
16 Dual LED indicators red: Raspberry Pi power indicator
green: Raspberry Pi operating statusindicator
17 TF card slot (bottom side) insert a Micro SD card with pre-burnt system, to start up Compute Module 4 Lite




Writing Image

1、 If your Compute Module 4 (CM4 hereafter) is the LITE version, you just need to write the image to Micro SD card like Raspberry Pi boards.
2、 If your use the eMMC version, you need to connect the CM4 to PC by Micro USB cable, Download the rpiboot tools and install it as administrator
3、 Download newest Raspberry Pi OS image from Raspberry Pi Website.
Compute Module 4 IO Board 3.png
If you use the eMMC version, you need to connect the CM4 to the IO board. Connect the BOOT pin of IO board to the GND . Connect USB SLAVE Interface of IO board to PC. Connect 12V power adapter to IO Board. A device named BCMxxx is recognized, and you need to run the rpiboot software, to recognized eMMC of CM4 as an portable drive.
Compute-Module-4-1-1.png
4、 Format SD card: You need to format the MicroSD card or the eMMC by SDFormatter.exe software.
PI4-03.jpg
5、 Write image: You need to write the image to Micro SD card or the eMMC by Win32DiskImager.exe software. Select the image file and click “Write”. Please DO NOT format it after formatting.
PI4-04.jpg
6、 Booting: Insert the Micro SD card into the card slot and connect the 12V power adapter. Power indicator turn solid red and the ACT is green and blink while booting.
If you use the eMMC version, don't forget to disconnect the nRPI_BOOT J2 jumpers when powering off and reboot.
If you failed to write the eMMC, please try with the following steps:

  • User Windows PC instead of Windows 7 or Linux. It seems that Windows 7 or Linux PC is not stable for eMMC writing.
  • Check your CM4, make sure that it is the eMMC version which has one more eMMC chip compare to the LITE version..

Compute-Module-4-5.png

  • Note that you need to connect 12 power adapter to the Power port.
  • Please change a USB cable for a try and make sure that the cable is data accessible.
  • Change the USB port of the PC and try it again.
  • Try to restart your PC.
  • Re-connect the CM4 for a try.
  • Try with other PCs.

RTC FAN

To enable the I2C for Cooling fan and the RTC, you need to add the line "dtparam=i2c_vc=on" to config file
RTC is connected to i2c-10 with address 0x51(7bits)
FAN is connected to i2c-10 上 with address 0x2f(7bits)

sudo nano /boot/config.txt
#Add the following line to the end
dtparam=i2c_vc=on
#comment the line dtparam=audio=on
#dtparam=audio=on
#Save and reboot
sudo reboot

RTC test

1.Download the test demo.

Open the terminal of the Raspberry Pi, enter the following command:

sudo apt-get install p7zip-full
sudo wget https://www.waveshare.net/w/upload/4/42/PCF85063_code.7z
7z x PCF85063_code.7z -O./
cd PCF85063_code

2.Run the demo

C

Execute the following commands to compile and execute the test demo:

cd c
sudo make clean
sudo make -j 8
sudo ./main

And then you can check the running result as below:

RTC PCF85063 c test.png

Python

Enter the python/example directory:

cd python/example

And then run the python demo, the demo can support python2/3

# python2
sudo python main.py
# python3
sudo python3 main.py

The running result as below:

RTC PCF85063 python test.png

FAN test

【Note】Please connect the fan first before connecting the power to the PoE Board to complete! Please do not connect the fan to the PoE Board when the board is powered on(the fan control chip is powered on,), otherwise, the EMC2301 chip will be damaged!

Open the terminal of the Raspberry Pi, enter the following command:

sudo apt-get install p7zip-full
sudo wget https://www.waveshare.net/w/upload/5/56/EMC2301_code.7z
7z x EMC2301_code.7z -O./
cd EMC2301_code

C

Compile and execute the test demo:

cd c
sudo make clean
sudo make -j 8
sudo ./main

python

Enter the python/example directory:

cd python/example

And then run the python demo, the demo can support python2/3

# python2
sudo python main.py
# python3
sudo python3 main.py

The fan will run the variable speed test in RPM mode. Pay attention to the changes of the fan's sound. The running phenomena of the python demo are the same as the C program. The terminal will output the relevant data of the fan at the same time, as shown in the picture below:

FAN EMC2301 test.png

You can also directly control the fan speed by modifying the parameter of the demo.

CSI DSI

CSI and DSI are disabled by default. I2C-10、I2C-11、I2C-0 should be used for Camera and DSI displays.
Open a terminal and run the following commands:

 sudo apt-get install p7zip-full
 wget https://www.waveshare.com/w/upload/4/41/CM4_dt_blob.7z
 7z x CM4_dt_blob.7z -O./CM4_dt_blob
 sudo chmod 777 -R CM4_dt_blob
 cd CM4_dt_blob/
 #If you want to use both cameras and DSI0
 sudo  dtc -I dts -O dtb -o /boot/dt-blob.bin dt-blob-disp0-double_cam.dts
 #If you want to ue both cameras and DSI1
 sudo  dtc -I dts -O dtb -o /boot/dt-blob.bin dt-blob-disp1-double_cam.dts
 #HDMI1 is disabled if you use DSI interfaces for displayin. HDMI1 cannot work even thought you just built the file without connecting DSI display, please note it.
 #If you want to enable the HDMI1, please remove the dt-blob.bin file with the command: '''sudo rm -rf /boot/dt-blob.bin'''
 #Turn off IO Board and re-power the CM4

Connect Cameras and DSI display
1: Please first disconnect power off the IP Board when connecting.
2: Use CM-DSI-ADAPTER to connect Compute Module 4 PoE Board and DSI displays
3: UseCSI adapter cable to connect Compute Module 4 PoE Board and CSI cameras.
3: Connect the power adapter
4: Wait for booting.
5: If the DSI display cannot work, please check if you have added /boot/dt-blob.bin and reboot.
6: Please enable camera by raspi-config, choose Interfacing Options->Camera->Yes->Finish-Yesand reboot

Reference:

Test RPi Camera:
Test video0:

sudo raspivid -t 0 -cs 0

Test video1:

sudo raspivid -t 0 -cs 1


Pinput

Compute-Module-4-1-21.png

No. PIN Description
1 PI BOOT The pin is low when booting. This pin is connected to USB SLAVE interface.
2 EEPROM WP Set it to LOW to avoid writing EEPROM
3 IP1/0 MXL7704 AN1/0 Pin of CM4 board
4 VADC COMP Video output
5 ETH IN ETH synchronize signal
6 PI_EN Synchronize with PI_RUN signal
7 PI_GLOBAL_EN MXL7704 power enable pin of CM4, Low to disable.
8 PI_RUN CM4 status pin, high for On. Pull-down it to foruce reset the CM4
9 WIFI_EN WIFI enable pin, Low to disbale, and NC to enable.
11 BT_EN Bluetooth enable pin, Low to disable and NC to enable.





If you require technical support, please go to the Support page and open a tickets.
Retrieved from "https://www.waveshare.com/w/index.php?title=Compute_Module_4_POE_Board&oldid=21802"