Difference between revisions of "7inch HDMI LCD (H) (with case)"

From Waveshare Wiki
Jump to: navigation, search
Line 45: Line 45:
  
 
== Working with Raspberry Pi ==
 
== Working with Raspberry Pi ==
For the Windows OS on PC, the resolution of the LCD is automatically identified. Hence, you do not need to make the relative settings. When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.
+
Supports Raspbian/Ubuntu mate/Windows 10 iot Core
  
Turn on the "backlight" switch then connect the LCD to your Pi (HDMI Port of LCD -> HDMI Port of Pi; USB Port of LCD -> USB Port of Pi; 5V~2A power supply). Download the Raspbian image from [https://www.raspberrypi.org/downloads/ Raspberry Pi web site]. Write the image to a TF card and append the following lines to the config.txt file which is located in the root of your TF card:
+
When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.
 +
 
 +
Download the Raspbian image from [https://www.raspberrypi.org/downloads/ Raspberry Pi web site]. Write the image to a TF card and append the following lines to the config.txt file which is located in the root of your TF card:
 
<pre>
 
<pre>
 
max_usb_current=1
 
max_usb_current=1
hdmi_group=2
+
hdmi_force_hotplug=1
hdmi_mode=87
+
config_hdmi_boost=10
 +
hdmi_group=2  
 +
hdmi_mode=87  
 
hdmi_cvt 1024 600 60 6 0 0 0
 
hdmi_cvt 1024 600 60 6 0 0 0
hdmi_drive=1
 
 
</pre>
 
</pre>
 
You must make sure that there are no spaces on either side of the equal sign.
 
You must make sure that there are no spaces on either side of the equal sign.
 +
 +
Connect the Touch interface of LCD to USB port of Raspberry Pi
 +
 +
Connect HDMI interface of LCD to HDMI port of Raspberry Pi
  
 
Save and connect the TF card to your Pi then power up.
 
Save and connect the TF card to your Pi then power up.
  
(Touch input working well means that the LED firmware is Rev2.1. If the LCD firmware is 1.1, see [[#About LCD revision]])
 
  
 
'''Note: '''
 
'''Note: '''

Revision as of 07:46, 7 December 2017

7inch HDMI LCD (H) (with case)
Supports various systems
7inch-HDMI-LCD-H-with-Holder-1.jpg

7 inch Capacitive Touch Screen LCD, HDMI interface, supports various systems
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Introduction

1024×600, 7 inch Capacitive Touch Screen LCD, HDMI interface, supports various systems。 Toughened glashh capacitive touch panel, 6H hardness

More

Features

  • 7inch IPS screen, 1024x600 hardware resolution, onfigurable by software (up to 1920x1080)
  • Toughened glass capacitive touch panel, 6H hardness
  • Supports popular mini PC such as Raspberry Pi, BB Black, Banana Pi
  • Used with Raspberry Pi, supports Raspbian, Ubuntu, WIN 10 IOT, single touch and driver free
  • Multi languages OSD menu, for power management, brightness/contrast adjustment, etc
  • 3.5mm audio jack, supports HDMI audio output
  • Supports VGA input (specific cable is required and should be purchase separately)
  • High quality PC case, optional tilt angle: 30°/50°

Working with PC

This product supports Windows 10/8.1/8/7 OS.:
1. Connect the TOUCH interface of LCD to the USB interface of PC . Waiting for a moment, The touch will be recognized by Windows automatically
2. If you use HDMI, you need to connect the HDMI interface of LCD to the HDMI port of PC. About 5s later, you can see that the LCD display properly. If you need the audio, if you insert a 3.5mm earphones to HP ports.
3. Use VGA,you need to connect the VGA interface of LCD to PC's VGA ports by Mini HDMI to VGA Cable
Note:
1) If multi screen are connected to one PC at the same time, you can only control the cursor by this LCD, so please set the LCD as main screen.
2) Some of PC cannot support HDMI screen Hot Plug . In this case, restart the PC can solve.
3) Sometimes LCD will flicker because of undersupply from USB cable of PC. You need to connect an external power supply (5V/2A) to DC port.
4) HP audio output only works while using HDMI communication
5) Mini HDMI to VGA Cable is necessary and need to be purchased separately if you use VGA communication.

Working with Raspberry Pi

Supports Raspbian/Ubuntu mate/Windows 10 iot Core

When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.

Download the Raspbian image from Raspberry Pi web site. Write the image to a TF card and append the following lines to the config.txt file which is located in the root of your TF card:

max_usb_current=1
hdmi_force_hotplug=1 
config_hdmi_boost=10
hdmi_group=2 
hdmi_mode=87 
hdmi_cvt 1024 600 60 6 0 0 0

You must make sure that there are no spaces on either side of the equal sign.

Connect the Touch interface of LCD to USB port of Raspberry Pi

Connect HDMI interface of LCD to HDMI port of Raspberry Pi

Save and connect the TF card to your Pi then power up.


Note:

  • Resolution of Ubuntu Mate OS or Windows 10 IoT Core OS can also be set properly by editing config.txt.
  • For Pi Zero / Zero W: if you've used an SD card on a Pi 3 and then attached the card to the Pi Zero, the touch screen often doesn't work. In such cases, you have to write a fresh system image to the SD card. The first boot up must be done on the Pi Zero but not Pi 3, due to initialization for a corresponding device.

About LCD revision

An LCD with Rev 2.1 firmware does not require any drivers, that is, touch function works properly without installing any software. So we did not provide any drivers and images for Rev 2.1 LCDs. The following drivers are only available for the LCD with Rev 1.1 firmware. But if you install the driver to the Rev 2.1 one, it will lead touch function not to work.

Rev2.1 New Features

  • Upgrade to IPS screen, wider viewing angle, more clear displaying.
  • Standard HID protocol, easy to be integrated into your system.
  • For the Raspberry Pi, supports Raspbian, Ubuntu Mate, single touch, and driver free.
  • When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free.

Rev1.1 and before

  • For the Raspberry Pi, comes with Raspbian driver (works with your Raspbian directly), and Ubuntu image.
  • When work as a computer monitor, touch function is unavailable.

How to distinguish

  • See the backside of your LCD. The Revision number "Rev2.1" printed means that the LCD firmware is Rev 2.1.
  • However, "Rev1.1" printed on the backside doesn't mean that the LCD firmware must be Rev 1.1. Generally speaking, a LCD shipped after January 1, 2016 may be a Rev 2.1 one, although it was printed "Rev1.1".

Note: The only difference between Rev 1.1 and Rev 2.1 is the firmware, but hardware solutions, placement and routing are all the same. (PCB printings might be different due to different production batches.)

You can verify the firmware by these steps:

1. Using Raspberry Pi: Connect the LCD to your Pi (HDMI Port of LCD -> HDMI Port of Pi; USB Port of LCD -> USB Port of Pi; 5V~2A power supply). Download the image, e.g. Raspbian, from Raspberry Pi web site. Write the image to a TF card and add the following code to the end of /boot/config.txt:

max_usb_current=1
hdmi_group=2
hdmi_mode=87
hdmi_cvt 1024 600 60 6 0 0 0
hdmi_drive=1

You must make sure that there are no spaces on either side of the equal sign.

Save and connect the TF card to your Pi then power up. If touch works, that means the firmware revision is Rev 2.1.

2. Without Raspberry Pi: A PC (Windows 10/8.1/8/7) is required which cannot connect with other display device. Connect the LCD to your PC (USB Port of LCD -> USB Port of PC; HDMI Port of LCD -> HDMI Port of PC. Please first connect the USB Ports then connect the HDMI Port). If a new touch drive is recognized by Windows, that means the firmware revision is Rev 2.1. In this case, after the driver successfully installed, you can use the LCD as a human interface device.

  • If the touch function doesn't work properly after these steps, the firmware revision is often Rev 1.1, which can also work by other methods, see Rev 1.1 Manual.

Detailed infomation

Depending on the firmware, please view the instructions of different revision:

Resources

An LCD with Rev 2.1 firmware does not require any driver, that is, touch function works properly without installing any software. So we did not provide drivers for Rev 2.1 LCDs.

7inch HDMI LCD (C) image - used for the LCD with firmware Rev2.1
Download Link mini PC version
Latest official Raspbian image Raspberry Pi Raspbian
7inch HDMI LCD (C) Angstrom image Angstrom Beaglebone Black
7inch HDMI LCD (C) Raspbian image Banana Pi / Banana Pro Raspbian
7inch HDMI LCD (C) Lubuntu image Banana Pi / Banana Pro Lubuntu
7inch HDMI LCD (C) image - used for the LCD with firmware Rev1.1
Download Link mini PC version
RPI3_RPI2_7.0_1024x600_cap_usb_touch_HID_2016-05-27-raspbian-jessie_4.4.13v7_20160620.7z Raspberry Pi 3B/2B Raspbian 2016-05-27 jessie
7inch HDMI LCD (C) Raspberry B / B+ Raspbian image 2015-11-21 jessie Raspberry Pi B/B+ Raspbian 2016-11-21 jessie
7inch HDMI LCD (C) Raspberry 2 Model B Ubuntu image Raspberry Pi 2B Ubuntu
7inch HDMI LCD (C) Angstrom image Beaglebone Black Angstrom
7inch HDMI LCD (C) Raspbian image Banana Pi / Banana Pro Raspbian
7inch HDMI LCD (C) Lubuntu image Banana Pi / Banana Pro Lubuntu

Drivers for Raspbian (only support Rev1.1 LCD)

Out of date, Not available for any Raspbian OS later than 27-May-2016.

3D Drawings

LCD Panel Dimension

Anti-Piracy

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They're usually some poor copies of our early hardware revisions, and comes with none support service.

To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing:

RPi-LCD-Anti-Piracy.jpg

(Click to enlarge)

Beware of knock-offs

Please note that we've found some poor copies of this item in the market. They are usually made of inferior materials and shipped without any testing.

You might be wondering if the one you're watching or you've purchased in other non-official stores is original, feel free to contact us.

Support

Support

If you require technical support, please go to the Support page and open a ticket.