Difference between revisions of "4.3inch HDMI LCD"

From Waveshare Wiki
Jump to: navigation, search
Line 20: Line 20:
 
<!--{{4.3inch HDMI LCD Manual}}-->
 
<!--{{4.3inch HDMI LCD Manual}}-->
 
== Resource ==
 
== Resource ==
 +
===User Manual===
 +
*[https://www.waveshare.com/w/upload/f/fd/4.3inch_HDMI_LCD_User_Manual_EN.pdf 4.3inch HDMI LCD User Manual]
 
=== Driver ===
 
=== Driver ===
 
{{RPI LCD DRIVER}}
 
{{RPI LCD DRIVER}}
Line 33: Line 35:
 
===Certification===
 
===Certification===
 
*[https://www.waveshare.com/w/upload/c/cb/4.3inch_HDMI_LCD_Certification.rar CE RoHS]
 
*[https://www.waveshare.com/w/upload/c/cb/4.3inch_HDMI_LCD_Certification.rar CE RoHS]
 +
 
== FAQ ==
 
== FAQ ==
 
{{RPI HDMI GPIO LCD FAQ}}
 
{{RPI HDMI GPIO LCD FAQ}}

Revision as of 10:19, 10 January 2019

4.3inch HDMI LCD
480×272
4.3inch-HDMI-LCD-1.jpg

4.3inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Introduction

4.3inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi

More

Resource

User Manual

Driver

The driver can be downloaded from github

git clone https://github.com/waveshare/LCD-show.git

Software

Image

Description: if you felt hard to install driver, try the image with driver pre-installed.

LCD Panel Dimension

Certification

FAQ

 Answer:
The LCD must have a driver installed for normal use. For details, please refer to the relevant introduction in the user manual.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
Since the Raspberry Pi image and version are frequently updated, if you encounter a situation where the LCD cannot be used normally, please download the latest version of the image provided by us or from the official website of Raspberry Pi and install the latest driver provided by us.
  • Make sure the hardware connection is correct and the contact is good.
  • Make sure that TF card programming is normal.
  • When the Raspberry Pi starts normally, the PWR light is always on, and the ACT light is flashing. If it is found that both lights are always on, it may be that the TF card is not successfully programmed to the image or the TF card is in poor contact with the Raspberry Pi.
  • It is recommended to use a 5V 2.5A power adapter for the Raspberry Pi. If the Raspberry Pi is powered by the USB port of the PC, the Raspberry Pi may not be able to start normally due to an insufficient power supply.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
Commercial grade (0~70 degrees Celsius).
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
When working with 5V input, the current is about 200mA.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
When working with 5V input, the current is about 200mA with back light on and 30mA with back light off.
{{{3}}}
{{{4}}}

{{{5}}}


Anti-Piracy

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They're usually some poor copies of our early hardware revisions, and comes with none support service.

To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing:

RPi-LCD-Anti-Piracy.jpg

(Click to enlarge)

Support

Support

If you require technical support, please go to the Support page and open a ticket.