Revision as of 08:10, 1 June 2023

13.3inch PiPad

Mini-Computer Powered by Raspberry Pi 3A+, 13.3inch HD Touch Screen, USB / ETH Ports

Overview

Introduction

Mini-Computer Powered by Raspberry Pi 3A+, 13.3inch HD Touch Screen, USB / ETH Ports

more

Features

13.3inch IPS screen,1920 x 1080 high resolution.
Embed Raspberry Pi 3A+ as controller.
Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch.
Embedded ferrite Hi-Fi speaker.
Embedded Microphone And Speaker, Adopts Snowboy Hotword Detection Engine.
75 x 75mm spacing mounting holes (M4 screw hole).
Comes with a 75° tilt angle stand.

Difference between Migic mirror and Pipad

The only difference between Magic mirror and the Pipad is that the Magic mirror use one-way mirror and the Pipad use Toughened Glass.

User Guide

To use the Magic mirror, you can use the pre-configured image which we provide or configure it yourself with the original Raspbian image. It is recommended to install pre-configured images for newbies or first-time installations. The pre-configured images have already installed the required libraries and drivers, and the program runs automatically after booting.

Method 1. Pre-configured image

1. Download the pre-configured image and write it to your SD card.

Image for 13.3inch Magic Mirror

2. Add the following lines to wpa_supplicat.conf files in the BOOT directory. (if you didn't find the files, create them.)

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=US
 
network={
        ssid="your_real_wifi_ssid"
        psk="your_real_password"
}

Note: you need to change your_real_wifi_ssid and your_real_password" to the real ssid and password.

3. Inset the card to Raspberry Pi and power on it.

Method 2. Configure image manually

1. Write a Raspbian image: Download the lasted Raspbian image from the Rasberry Pi website and write it to an empty micro SD card.; Create a new Txt file under the BOOT directory of the micro SD card and name it SSH.; Modify the config.txt file which is located in the BOOT directory, and add the following lines to the config.txt file

hdmi_group=2
hdmi_mode=82
hdmi_cvt 1920 1080 60 6 0 0 0

Save and insert the micro SD card into Raspberry Pi.; Connect the Magic mirror to the network and power on Raspberry Pi.; After booting, you can access Raspberry Pi via SSH, or directly connect the keyboard and mouse.
2. Install WM8960 sound card driver: Open the terminal and use the following commands to install.

git clone https://github.com/waveshare/WM8960-Audio-HAT
cd WM8960-Audio-HAT
sudo ./install.sh

Modify the config.txt file, remove the following line from the file, or comment on it.

#dtparam=audio=on

Then reboot Raspberry Pi

sudo reboot

After rebooting, check the driver by the following command.

sudo dkms status

If you can get the information below, it means that the driver was installed successfully.

wm8960-soundcard, 1.0, 4.19.58-v7l+, armv7l: installed

Test the sound card

Test playing: aplay -l

pi@raspberrypi:~ $ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: wm8960soundcard [wm8960-soundcard], device 0: bcm2835-i2s-wm8960-hifi wm8960-hifi-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Test recording: arecord -l

pi@raspberrypi:~ $ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: wm8960soundcard [wm8960-soundcard], device 0: bcm2835-i2s-wm8960-hifi wm8960-hifi-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

3. Install Magic Mirror driver: Open the terminal and type the following commands.

curl -sL https://deb.nodesource.com/setup_10.x | sudo -E bash -
sudo apt install -y nodejs
git clone https://github.com/MichMich/MagicMirror
cd MagicMirror/
npm install

After installing, run the command to display.

DISPLAY=:0 npm start

Install MMM-VoiceAssistant model and display.

cd ~/MagicMirror/modules
git clone https://github.com/waveshare/MMM-VoiceAssistant.git
cd MMM-VoiceAssistant
cp config/config.js.en ~/MagicMirror/config/config.js  #Display English
#cp config/config.js.cn ~/MagicMirror/config/config.js  #Display Chinese
cd ~/MagicMirror
DISPLAY=:0 npm star

4. Install Python3 virtual environment

sudo apt-get update
sudo apt-get install python3-dev python3-venv
python3 -m venv env
env/bin/python -m pip install --upgrade pip setuptools wheel
source env/bin/activate

Note: The following steps should be taken in the virtual environment, if you close the terminal and restart it, you should use the command below to enter the environment again first.

source ~/env/bin/activate

5. Install snowboy: Install libraries

sudo apt-get install swig
sudo apt-get install libatlas-base-dev
sudo apt-get install portaudio19-dev
sudo apt-get install flac
pip3 install PyAudio
pip3 install SpeechRecognition

Download snowboy

git clone https://github.com/Kitt-AI/snowboy.git
cd snowboy/swig/Python3
make
cd ../../examples/Python3

Modify snowbiydecoder.py file. Change from.import snowboydetect to import snowboydetect. Save and enable snowboy

cd ~/snowboy/examples/Python3
python3 demo.py resources/models/smart_mirror.umdl

Try to say smart mirror, you will hear ding and the information below are printed on the mirror

INFO:snowboy:Keyword 1 detected at time: 2019-12-03 11:30:16

6. Install Google Assistant Service: Create .asoundrc file in /home/pi directory （the user directory）

nano .asoundrc

Add the following lines to the .asoundrc file

pcm.!default {
  type asym
  capture.pcm "mic"
  playback.pcm "speaker"
}
pcm.mic {
  type plug
  slave {
    pcm "hw:0,0"
  }
}
pcm.speaker {
  type plug
  slave {
    pcm "hw:0,0"
  }
}

According to the official guide to installing Google Assistant Service.

https://developers.google.com/assistant/sdk/guides/service/python

Please follow the third step of the official guide to configure and create OAuth Client ID JSON file. Don't forget to copy the JSON file to your Raspberry Pi.

Following the fourth step of the guide to register the device model.

Install Google Assistant SDK.

(env) $ sudo apt-get install portaudio19-dev libffi-dev libssl-dev
(env) $ python -m pip install --upgrade google-assistant-sdk[samples]

Authorize model

(env) $ python -m pip install --upgrade google-auth-oauthlib[tool]

Genegrate credential

(env) $ google-oauthlib-tool --scope https://www.googleapis.com/auth/assistant-sdk-prototype \
      --save --headless --client-secrets /path/to/client_secret_ client-id .json

Then you will get an URL, please copy it and open it on the browser of your PC.

Please visit this URL to authorize this application: https://...

Go to the URL, you are asked to log in to your Google Account and get the authorization code by following the guides, Copy the code to the terminal.

Please go to this URL: https://...
Enter the authorization code:

If the authorization process is done successfully, you will get the information as below.

credentials saved: /path/to/.config/google-oauthlib-tool/credentials.json

Use the following command to test.

googlesamples-assistant-pushtotalk --project-id my-dev-project --device-model-id my-model

Note: my-dev-project is the Google Could Platform ID of Actions Console project you created. You need to find the project ID in the Actions Console. my-model is the device model name you create; Press Enter, and try to ask something.
7. Set auto-run: Install PM2.

sudo npm install -g pm2

Setup pm2

pm2 startup

You will get the information below, please copy the command and run it on the terminal.

[PM2] To setup the Startup Script, copy/paste the following command:
sudo env PATH=$PATH:/usr/bin /usr/lib/node_modules/pm2/bin/pm2 startup systemd -u pi --hp /home/pi

Run Magic mirror by PM2.

cd MagicMirror/modules/MMM-VoiceAssistant/pi
pm2 start mm.sh

Run snowbiy by PM2

cd MagicMirror/modules/MMM-VoiceAssistant/pi
pm2 start snowboy.sh

Set auto-run.

pm2 save

If you want to disable the services, you can also use the following command.

pm2 stop mm
pm2 stop snowboy

8. kepp display lighting all the time: Modify lightdm.conf

sudo nano /etc/lightdm/lightdm.conf

Find the line "Xserver-command" below [SeatDefaults] section and change it from

#xserver-command=X

to

xserver-command=X -s 0 -dpms

Then save and reboot.

sudo reboot

Note

1. If the wakeup word is unworkable for you, please log in snowboy website: https://snowboy.kitt.ai , And add the new wakeup word.; Click recording icon to record voice and test if the voice model is workable; Download the model file and copy it to ~/MagicMirror/modules/MMM-VoiceAssistant/pi direcotory.; Modify snowboy.sh file

nano snowboy.sh

Modify the name to the the one you download, for English, you need to modify the snowboy.umdl to the yours

cd ~/MagicMirror/modules/MMM-VoiceAssistant/pi
~/env/bin/python3 demo.py smart_mirror.umdl snowboy.umdl

2. Google Assistant Service can only support 500 request every day.

Open ~/MagicMirror/modules/MMM-VoiceAssistant/pi/audiofileinput.py. You can enter the following code<br\>

Follow the previous Google Assistant Service installation section to register an account, device model, and install authorization.
Finally, replace DEVICE_ID and DEVICE_MODEL_ID in the program with the corresponding values

Resource

Drawing

13.3inch HDMI LCD 3D Drawing

Software

Authentication Information

CE RoHS

Support

If you require technical support, please go to the Support page and open a ticket.

@@ Line 53: / Line 53: @@
 ===Method 2. Configure image manually===
-;1. Write Raspbian image
+;1. Write a Raspbian image
 : Download the lasted Raspbian image from the Rasberry Pi website and write it to an empty micro SD card.
-: Create a new txt file under the BOOT directory of micro SD card and name it as SSH.
+: Create a new Txt file under the BOOT directory of the micro SD card and name it SSH.
-: Modify config.txt file which is located at BOOT directory, add the following lines to config.txt file
+: Modify the config.txt file which is located in the BOOT directory, and add the following lines to the config.txt file
 <pre>
 hdmi_group=2
@@ Line 62: / Line 62: @@
 hdmi_cvt 1920 1080 60 6 0 0 0
 </pre>
-: Save and insert the micro SD card to Raspberry Pi.
+: Save and insert the micro SD card into Raspberry Pi.
-: Connect the Magic mirror to network and power on Raspberry Pi.
+: Connect the Magic mirror to the network and power on Raspberry Pi.
-: After booting, you can access Raspberry Pi via SSH, or directly connect keyboard and mouse.
+: After booting, you can access Raspberry Pi via SSH, or directly connect the keyboard and mouse.
 ;2. Install WM8960 sound card driver
-: Open the terminal and use the following commands to install
+: Open the terminal and use the following commands to install.
 <pre>
 git clone https://github.com/waveshare/WM8960-Audio-HAT
@@ Line 72: / Line 72: @@
 sudo ./install.sh
 </pre>
-: Modify config.txt file, remove the following line from the file or comment it.
+: Modify the config.txt file, remove the following line from the file, or comment on it.
 <pre>
 #dtparam=audio=on
@@ Line 80: / Line 80: @@
 sudo reboot
 </pre>
-: After rebooting, check the driver by the following command
+: After rebooting, check the driver by the following command.
 <pre>
 sudo dkms status
 </pre>
-: If you can get the information as below, it means that the driver was installed successfully.
+: If you can get the information below, it means that the driver was installed successfully.
 <pre>
 wm8960-soundcard, 1.0, 4.19.58-v7l+, armv7l: installed
 </pre>
-:Test the sound card
+: Test the sound card
 *Test playing: aplay -l
 <pre>
@@ Line 106: / Line 106: @@
 </pre>
 ;3. Install Magic Mirror driver
-: Open terminal and type the following commands
+: Open the terminal and type the following commands.
 <pre>
 curl -sL https://deb.nodesource.com/setup_10.x | sudo -E bash -
@@ Line 114: / Line 114: @@
 npm install
 </pre>
-:After installing, run the command to display
+: After installing, run the command to display.
 <pre>
 DISPLAY=:0 npm start
 </pre>
 :[[File:MgicMirror-1.png|600px]]
-: Install MMM-VoiceAssistant model and display
+: Install MMM-VoiceAssistant model and display.
 <pre>
 cd ~/MagicMirror/modules
@@ Line 138: / Line 138: @@
 source env/bin/activate
 </pre>
-:'''Note: The following steps should be take in the virtual environment, if you close the terminal and restart it, you should use the command below to enter the environment again firstly'''
+:'''Note: The following steps should be taken in the virtual environment, if you close the terminal and restart it, you should use the command below to enter the environment again first.'''
 <pre>
 source ~/env/bin/activate
 </pre>
 ;5. Install snowboy
-:Install libraries
+: Install libraries
 <pre>
 sudo apt-get install swig
@@ Line 152: / Line 152: @@
 pip3 install SpeechRecognition
 </pre>
-:Download snowboy
+: Download snowboy
 <pre>
 git clone https://github.com/Kitt-AI/snowboy.git
@@ Line 193: / Line 193: @@
 }
 </pre>
-:Accoding to the official guide to install Google Assistant Service
+: According to the official guide to installing Google Assistant Service.
 *https://developers.google.com/assistant/sdk/guides/service/python
-:Please follow the third step of the official guide to configure and create OAuth Client ID JSON file. Don't forget to copy the JSON file to your Raspberry Pi.
+: Please follow the third step of the official guide to configure and create OAuth Client ID JSON file. Don't forget to copy the JSON file to your Raspberry Pi.
-:Following the fourth step of the guide to register device model
+: Following the fourth step of the guide to register the device model.
-: Install Google Assistant SDK
+: Install Google Assistant SDK.
 <pre>
 (env) $ sudo apt-get install portaudio19-dev libffi-dev libssl-dev
@@ Line 211: / Line 211: @@
        --save --headless --client-secrets /path/to/client_secret_ client-id .json
 </pre>
-: Then you will get an URL, please copy it and open it on browser of your PC.
+: Then you will get an URL, please copy it and open it on the browser of your PC.
 <pre>
 Please visit this URL to authorize this application: https://...
 </pre>
-: Go to the URL, you are asked to log in your Google Account and get the authorization code by following guides, Copy the code to the terminal
+: Go to the URL, you are asked to log in to your Google Account and get the authorization code by following the guides, Copy the code to the terminal.
 <pre>
 Please go to this URL: https://...
@@ Line 224: / Line 224: @@
 credentials saved: /path/to/.config/google-oauthlib-tool/credentials.json
 </pre>
-:Use the following commandto test.
+: Use the following command to test.
 <pre>
 googlesamples-assistant-pushtotalk --project-id my-dev-project --device-model-id my-model
 </pre>
-: Note: my-dev-project is the Google Could Platform ID of Actions Console porject you created. You need to find the project ID  in Actions Console. my-model is the device model name you create
+: Note: my-dev-project is the Google Could Platform ID of Actions Console project you created. You need to find the project ID  in the Actions Console. my-model is the device model name you create
-:Press Enter, and try to ask something.
+: Press Enter, and try to ask something.
 ;7. Set auto-run
-:Install PM2
+: Install PM2.
 <pre>
 sudo npm install -g pm2
@@ Line 239: / Line 239: @@
 pm2 startup
 </pre>
-:You will get informatin below, please copy the command and run it on terminal
+: You will get the information below, please copy the command and run it on the terminal.
 <pre>
 [PM2] To setup the Startup Script, copy/paste the following command:
 sudo env PATH=$PATH:/usr/bin /usr/lib/node_modules/pm2/bin/pm2 startup systemd -u pi --hp /home/pi
 </pre>
-:Run Magic mirror by PM2
+: Run Magic mirror by PM2.
 <pre>
 cd MagicMirror/modules/MMM-VoiceAssistant/pi
 pm2 start mm.sh
 </pre>
-:Run snowbiy by PM2
+: Run snowbiy by PM2
 <pre>
 cd MagicMirror/modules/MMM-VoiceAssistant/pi
 pm2 start snowboy.sh
 </pre>
-:Set auto-run
+: Set auto-run.
 <pre>
 pm2 save
 </pre>
-:If you want to disable the sevices, you can aslo use the following command
+: If you want to disable the services, you can also use the following command.
 <pre>
 pm2 stop mm
@@ Line 264: / Line 264: @@
 </pre>
 ;8. kepp display lighting all the time
-:Modify lightdm.conf
+: Modify lightdm.conf
 <pre>
 sudo nano /etc/lightdm/lightdm.conf
 </pre>
-:Find the line "Xserver-command" below [SeatDefaults] section and change it from
+: Find the line "Xserver-command" below [SeatDefaults] section and change it from
 <pre>
 #xserver-command=X
@@ Line 276: / Line 276: @@
 xserver-command=X -s 0 -dpms
 </pre>
-: Then save and reboot
+: Then save and reboot.
 <pre>
 sudo reboot

Navigation menu

Difference between revisions of "13.3inch PiPad"