Difference between revisions of "10.1inch HDMI LCD"

From Waveshare Wiki
Jump to: navigation, search
Line 3: Line 3:
 
|img=[[File:10.1inch-HDMI-LCD-1.jpg|300px|link=http://www.waveshare.com/10.1inch-hdmi-lcd.htm]]
 
|img=[[File:10.1inch-HDMI-LCD-1.jpg|300px|link=http://www.waveshare.com/10.1inch-hdmi-lcd.htm]]
 
|caption=10.1inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi
 
|caption=10.1inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi
|category=[[:Category:OLEDs / LCDs|OLEDs / LCDs]], [[:Category:LCD|LCD]], [[:Category:Raspberry Pi LCD|Raspberry Pi LCD]]
+
|category=[[:Category:OLEDs / LCDs|OLEDs / LCDs]], [[:Category:Raspberry Pi LCD|Raspberry Pi LCD]]
 
|brand=Waveshare
 
|brand=Waveshare
 
|{{#urlget:amazon|default}}=display
 
|{{#urlget:amazon|default}}=display

Revision as of 08:49, 28 September 2017

10.1inch HDMI LCD
1024×600
10.1inch-HDMI-LCD-1.jpg

10.1inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Introduction

10.1inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi

More

Features

  • 1024×600 high resolution
  • Resistive touch control
  • Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable)
  • Raspbian/Ubuntu Drivers are provided (works with your own Raspbian/Ubuntu directly)
  • Also works as a computer monitor, in this case, touch panel is unavailable and HDMI cable is required
  • HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os)
  • Back light control to lower power consumption

Getting Started

Hardware Connection

Hardware connection for Raspberry Pi Model A+/B+/2 B/3 B
Hardware connection for Raspberry Pi Zero
  1. Plug the LCD to your Raspberry Pi:
    • There are 40 pins on Raspberry Pi Model A+/B+/2 B/3 B but only 26 pins on the LCD, so you should pay attention to connecting the pins to your Pi accordingly.
  2. Connect the HDMI Connector to both the HDMI interfaces on the LCD and the Pi.
    • You should connect the LCD to Raspberry Pi Model B or Raspberry Pi Zero with an HDMI cable rather than an HDMI Connector.
  3. Turn on the "backlight" switch on the back of the LCD.

You can enable the touch in two ways: Method 1. install driver to your Raspbian/Ubuntu Mate OS. Method 2. use the Ready-to-use image file of which LCD driver was pre-installed.

Method 1. Driver installation

Description: The driver can be downloaded from github

git clone https://github.com/waveshare/LCD-show.git


1) Download the Raspbian / Ubuntu Mate image from Raspberry Pi website and extract it on a PC.

2) Connect your micro SD card to the PC and write the image to the card using Win32DiskImager. How to write an image to a micro SD card for your Pi? See RPi Image Installation Guides for more details)

3) Copy the LCD driver to the micro SD card (or copy the driver to the system of Pi using a USB drive).

4) Append the following lines to the config.txt file which is located in the root of the card:

max_usb_current=1
hdmi_group=2
hdmi_mode=87 
hdmi_cvt 1024 600 60 6 0 0 0
display_rotate=2

5) The LCD will display after booting up. Then open a terminal to install the touch driver which can be found in the /boot/ directory.

tar xzvf /boot/LCD-show-*.tar.gz  
cd LCD-show/
chmod +x LCD101-1024x600-show
./LCD101-1024x600-show

Touch function will work after restart. For ease of use, you can set the screen orientation, see: #Screen orientation settings.

Method 2. Using Ready-to-use image

The image file with pre-installed driver is located in the IMAGE directory of the CD, or you can download it from #Image. Extract the .7z file and you will get an .img file. Write the image to your micro SD card (How to write an image to a micro SD card for your Pi? See RPi Image Installation Guides for more details). Then insert the card to your Pi, power up and enjoy it.

Screen orientation settings

After touch driver installed, the screen orientation can be set by these commands:

  • 0 degree rotation
cd LCD-show/
./LCD101-1024x600-show 0
  • 90 degree rotation
cd LCD-show/
./LCD101-1024x600-show 90
  • 180 degree rotation
cd LCD-show/
./LCD101-1024x600-show 180
  • 270 degree rotation
cd LCD-show/
./LCD101-1024x600-show 270

Touch screen calibration

  • This LCD can be calibrated using a program called xinput_calibrator which can be downloaded from Xinput-calibrator_0.7.5-1_armhf
  • Extract and copy the software Xinput-calibrator_0.7.5-1_armhf.deb to the Raspbian of your Pi.
  • Install it with the commands:
sudo dpkg -i -B xinput-calibrator_0.7.5-1_armhf.deb 
  • Click the "Menu" button on the task bar, choose "Preference" -> "Calibrate Touchscreen".
  • Finish the touch calibration following the prompts. Maybe rebooting is required to make calibration active.
  • You can create a 99-calibration.conf file to save the touch parameters (not necessary if file exists).
/ect/X11/xorg.conf.d/99-calibration.conf
  • Save the touch parameters (may differ depending on LCD) to 99-calibration.conf, as shown in the picture:

5inch HDMI LCD FAQ1.jpg

Interface

PIN NO. SYMBOL DESCRIPTION
1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
3, 5, 7, 8, 10, 11, 12, 13, 15, 16, 18, 24 NC NC
6, 9, 14, 20, 25 GND Ground
19 TP_SI SPI data input of Touch Panel
21 TP_SO SPI data output of Touch Panel
22 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching
23 TP_SCK SPI clock of Touch Panel
26 TP_CS Touch Panel chip selection, low active

Resource

Driver

The driver can be downloaded from github

git clone https://github.com/waveshare/LCD-show.git

LCD Panel Dimension

Software

Image

Description: if you felt hard to install driver, try the image with driver pre-installed.

LCD Panel Dimension

FAQ

 Answer:
The LCD must have a driver installed for normal use. For details, please refer to the relevant introduction in the user manual.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
Since the Raspberry Pi image and version are frequently updated, if you encounter a situation where the LCD cannot be used normally, please download the latest version of the image provided by us or from the official website of Raspberry Pi and install the latest driver provided by us.
  • Make sure the hardware connection is correct and the contact is good.
  • Make sure that TF card programming is normal.
  • When the Raspberry Pi starts normally, the PWR light is always on, and the ACT light is flashing. If it is found that both lights are always on, it may be that the TF card is not successfully programmed to the image or the TF card is in poor contact with the Raspberry Pi.
  • It is recommended to use a 5V 2.5A power adapter for the Raspberry Pi. If the Raspberry Pi is powered by the USB port of the PC, the Raspberry Pi may not be able to start normally due to an insufficient power supply.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
Commercial grade (0~70 degrees Celsius).
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
When working with 5V input, the current is about 200mA.
{{{3}}}
{{{4}}}

{{{5}}}


 Answer:
When working with 5V input, the current is about 550mA with back light on and 100mA with back light off.
{{{3}}}
{{{4}}}

{{{5}}}


Anti-Piracy

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They're usually some poor copies of our early hardware revisions, and comes with none support service.

To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing:

RPi-LCD-Anti-Piracy.jpg

(Click to enlarge)

Support

Support

If you require technical support, please go to the Support page and open a ticket.