0.95inch RGB OLED (A)

0.95inch RGB OLED (A) 0.95inch RGB OLED, SPI interface, curved/horizontal pinheader

{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Primary Attribute Category: OLEDs / LCDs, OLED {{{userDefinedInfo}}}: {{{userdefinedvalue}}} Brand: Waveshare

Website International: Waveshare Website Chinese: 官方中文站点

Onboard Interfaces I2C SPI

Related Products 2.23inch OLED HAT 1.54inch LCD Module 1.5inch RGB OLED Module 1.5inch OLED Module 1.3inch OLED (B) 1.3inch OLED (A) 1.3inch OLED Module (C) 1.28inch LCD Module 1.14inch LCD Module 0.96inch OLED (B) 0.96inch OLED (A) 0.96inch LCD Module 0.95inch RGB OLED (B) 0.95inch RGB OLED (A) 0.91inch OLED Module

Specification

• Working Voltage: 3.3V/5V
• Communication Interface: SPI
• Screen Type: OLED
• Driver Chip: SSD1331
• Resolution: 96 x 64(Pixel)
• Dimension: 31.7 x 37 (mm)
• Display Color: RGB, 65K
• Operating Temperature(℃): -20°C ~ 70°C
• Storage Temperature(℃): -30°C ~ 80°C
• Visible Angle: >160°

Pinout

PIN	Description
VCC	3.3V/5V Power input
GND	Ground
NC	NC
DIN	SPI Data Input
CLK	SPI Clock input
CS	Chip select, low active
D/C	Command signal, low level for command, high level for data
RES	Reset signal, low active

PS: This module only has SPI interface, please pay attention when using it.

Resources

• User Manual
• Schematic
• Dimensions
• Code
• 0.95inch RGB OLED Datasheet
• Datasheets

FAQ

Question:How many volts can an OLED module be used in a system?

 Answer:

The OLED module is used in a 3.3V system by default, but after more than 24 hours of burn-in test, it is found that it can also work normally in a 5V system.

{{{3}}}

{{{4}}}

{{{5}}}

Question:How many hours is the service life of an OLED module?

 Answer:

Under normal working conditions, generally 50,000 hours.

{{{3}}}

{{{4}}}

{{{5}}}

Question:What is the working current of the OLED module?

 Answer:

At the operating voltage of 3.3V:

Working current of 0.95inch RGB OLED: about 38mA for full white display, about 4mA for full black display.
The working current of 0.96inch OLED is about 25mA when fully on, and 1.5mA when fully off.

Working current of 1.3inch OLED: about 29mA when fully on, 1.0mA when fully off.

{{{3}}}

{{{4}}}

{{{5}}}

Question:Why does the OLED module not turn on when it is connected to the power supply?

 Answer:

OLED has no backlight, and the display is self-illuminating. Only connect VCC and GND, the OLED will not light up.
Program control is required to brighten the OLED.

{{{3}}}

{{{4}}}

{{{5}}}

Question:What should I pay attention to when using this OLED module?

 Answer:

1. Be careful not to connect the power supply in reverse.
2. The same picture cannot be displayed for a long time, otherwise it will produce afterimages and cause damage to the OLED.

{{{3}}}

{{{4}}}

{{{5}}}

Support

If you require technical support, please go to the Support page and open a ticket.