STM32-QFP64, Programmer Adapter

SKU: 3467
Part Number: STM32-QFP64
Brand: Yamaichi




Yamaichi IC Test & Burn-in Socket with a simple board, specifically designed for STM32 microcontroller in QFP64(0.5mm pitch) package


  • 20-pin JTAG/SWD port and/or 4-pin USART1 interface for programming/testing
  • External crystal can be connected via on board socket for system clock
  • Onboard 32.768K crystal oscillator
  • Two LED indicators for testing, which are connected to the I/O pins via jumpers
  • All the MCU pins are accessible on expansion connectors
    • pin header pitch: 2.54mm(100mil)

Supported Devices

STM32 microcontroller in QFP64(0.5mm pitch) package with compatible pinouts:

  • STM32L1xxR series (STM32L151R8, STM32L152RB, etc.)
  • STM32F0xxR series (STM32F051RC, STM32F051RB, etc.)
  • STM32F1xxR series (STM32F103RC, STM32F100RB, etc.)
  • STM32F2xxR series (STM32F207RC, STM32F215RB, etc.)
  • STM32F3xxR series (STM32F303R8, STM32F373RB, etc.)
  • STM32F4xxR series (STM32F407RC, STM32F415RB, etc.)

Config the onboard "Device selection jumpers" according to the device to be programmed.

Outline and Dimensions

Unit: mm
Part NumberPitchPinsApplicable IC Dimensions (REF.)Outside Dimensions (REF.)
A x BC x DEFG x H
IC51-0644-807 0.5 64 10.0 x 10.0 12.0 x 12.0 11.3 - 32.0 x 35.0


  1. JTAG/SWD port
    • for programming/debugging/testing
    • compatible with ST-LINK / J-LINK / ULINK2 / STX-RLINK
  2. USART1 port
    • supports ISP and/or serial port debugging
  3. LED indicators
    • for quick testing
  4. Pin headers connected to MCU pins
    • clearly labeled with onboard marks
    • easy for testing and further expansion
  5. Boot mode configuration
    • configuring the BOOT0 and BOOT1 via jumpers
  6. 3.3V onboard regulator
    • AMS1117-3.3
  7. 5V power input
    • DC jack or 2-pin header
  8. External crystal socket
    • insert crystal to the holes on two sides, leave alone the middle hole
  9. Power indicator
  10. Device selection jumpers
    • short the upper headers for STM32F1xx / STM32L1xx / STM32F05x / STM32F3xx
    • short the lower headers for STM32F2xx / STM32F4xx
  11. LED jumpers
    • short the jumpers to connect LEDs to MCU I/O pins for testing
    • open the jumpers to disconnect
  12. 32.768K crystal (on bottom side)
    • for internal RTC with calibration

JTAG/SWD Connector Layout

The STM32-QFP64 houses JTAG/SWD headers for connecting a programmer. The connector layout is shown in the figure 1 below.

JTAG/SWD connector layout

Figure 1. JTAG/SWD connector layout

Boot Mode Configuration

Depending on the used pin configuration, the Flash memory, system memory or SRAM is selected as the boot space, as shown in Table 1 below.

STM32 boot mode configuration



Development resources:schematic, etc.

Weight: 0.09 kg

Quick Overview

  1. STM32-QFP64 × 1
  2. USB power cable × 1