Details
Integrates RGB interface LCD and 5-point capacitive touch (optional)
ESP32-S3-LCD-7
without touch control
ESP32-S3-Touch-LCD-7
with touch control
This product is a microcontroller development board with 2.4GHz WiFi and BLE 5 support, integrates high-capacity Flash and PSRAM. Onboard 7inch LCD screen can smoothly run GUI programs such as LVGL. Combined with various peripheral interfaces, suitable for the quick development of the HMI and other ESP32-S3 applications
- Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
- Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
- Built in 512KB of SRAM and 384KB ROM, with onboard 8MB PSRAM and 16MB Flash
- Onboard 7inch LCD display, 800×480 resolution, 65K color
- Supports 5-point capacitive touch control via I2C interface, with interrupt support (for touch version only)
- Onboard CAN, RS485, I2C interface and TF card slot, integrates full-speed USB port
- Supports flexible clock, module power supply independent setting, and other control to realize low power consumption in different scenarios
Excellent display performance, 170° viewing angle
Supports the expansion of multiple peripherals via Sensor, CAN, RS485, and I2C interfaces
for reference only, please refer to the Package Content for the detailed part list
- ESP32-S3N16R8
The SoC with WiFi and Bluetooth, up to 240MHz operating frequency, integrated 8MB PSRAM and 16MB Flash - 7inch display panel connector
- Touch panel connector
- TF card slot
- USB Type-C port
- UART1 Port
USB TO UART Type-C port - UART2 connector
UART1 and UART2 are the same UART, selected by switch - Sensor header
- CAN header
- I2C header
- RS485 header
- 3.7V single lithium battery PH2.0 header
- CAN terminal resistor selection
- RS485 terminal resistor selection
- UART selection
select UART1 or UART2 - BOOT button
Press and hold while powering on for program burning - RESET button
- I2C level selection
3.3V / 5V - DONE
Lithium battery charging completed indicator - CHG
Lithium battery charging indicator - PWR
Power supply indicator
ESP32-S3-LCD-7
ESP32-S3-Touch-LCD-7
Development Board Size
| Model | Basic Parameters | LCD Parameters | Communication interface | Others | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MCU | Flash | PSRAM | Resolution | Viewing Angle |
Touch Type |
CAN | RS485 | I2C | UART | Sensor | Digital Input |
Digital Output |
Dimensions (mm) | |||
ESP32-S3-Touch-LCD-4 Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 480 × 480 | 160° | capacitive | √ | √ | √ | - | - | - | - | without touch version: 76.54×74.66 (mm) with touch version: 84.2×84.2 (mm) |
||
ESP32-S3-Touch-LCD-4.3B Standard Ver. / Case Ver. |
ESP32-S3 | 16MB | 8MB | 800 × 480 | 160° | capacitive | √ | √ | √ | - | - | √ | √ | Standard version: 112.4×75.1 (mm) Case version: 116.3×79 (mm) |
||
ESP32-S3 4.3″ LCD Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 800 × 480 | 160° | capacitive | √ | √ | √ | - | √ | - | - | 106.1×67.8 (mm) | ||
ESP32-S3 5″ LCD Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 800 × 480 | 160° | capacitive | √ | √ | √ | - | - | √ | √ | 127.7×87.45 (mm) | ||
ESP32-S3 5″ LCD (B) Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 1024 × 600 | 178° | capacitive | √ | √ | √ | - | - | √ | √ | 127.7×87.45 (mm) | ||
ESP32-S3-Touch-LCD-7 Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 800 × 480 | 170° | capacitive | √ | √ | √ | √ | √ | - | - | without touch version: 165.72×97.60mm with touch version: 192.96×110.76mm |
||
ESP32-S3-Touch-LCD-7B Without Touch / With Touch |
ESP32-S3 | 16MB | 8MB | 1024 × 600 | 170° | capacitive | √ | √ | √ | √ | √ | - | - | without touch version: 165.72×97.60mm with touch version: 192.96×110.76mm |
||
Quick Overview
ESP32-S3-LCD-7
- ESP32-S3-LCD-7 x1
- HY2.0 2P to 2PIN male cable 10cm ×2
- HY2.0 3P to 3PIN male cable 10cm ×1
- HY2.0 4P to 4PIN male cable 10cm ×2
- Screws pack x1
ESP32-S3-Touch-LCD-7
- ESP32-S3-Touch-LCD-7 x1
- HY2.0 2P to 2PIN male cable 10cm ×2
- HY2.0 3P to 3PIN male cable 10cm ×1
- HY2.0 4P to 4PIN male cable 10cm ×2
- Screws pack x1






