Core746I, STM32 MCU core board

SKU: 11444
Part Number: Core746I
Brand: Waveshare

$44.99
$43.992+
$43.493+
$43.294+

Related Products:

Description

Details

STM32 STM32F746IGT6 MCU core board, full IO expander, JTAG/SWD debug interface
STM32F746IGT6 development board

Overview

Core746I is an STM32 MCU core board designed for STM32F746IGT6, supports further expansion. It is ideal for starting application development with STM32F family.

  • Minimal ready-to-run system, integrates clock circuit, USB power management, USB connector, etc.
  • Onboard 64M Bit SDRAM
  • All the I/O ports are accessible on the pin headers
  • JTAG/SWD programming/debugging interface
  • 2.0mm header pitch, allowed to be plugged-in your application board

What's on the Core746I

STM32F746IGT6 development board on board resource

  1. STM32F746IGT6:the high performance STM32 MCU which features:
    • Core: Cortex-M7 32-bit RISC + FPU + Chrom-ART graphic accelerator
    • Feature: single-cycle DSP instructions
    • Operating Frequency: 216MHz, 462 DMIPS/2.14 DMIPS/MHz
    • Operating Voltage: 1.7V-3.6V
    • Package: LQFP176
    • Memories: 1024kB Flash, 320+16+4kB SRAM
    • MCU communication Interfaces:
      • 6 x SPI, 4 x USART, 4 x UART, 3 x I2S, 4 x I2C
      • 2 x CAN, 1 x QUAD-SPI, 1 x DCMI, 2 x SAI
      • 1 x FMC, 1 x SDMMC, 14 x TIM , 1xLPTIM
      • 1 xLCD-TFT, 1xSPDIFRX, 1xHDMI-CEC
      • 1 x USB 2.0 OTG FS
      • 1 x USB 2.0 OTG HS (supports external HS PHY through ULPI)
      • 1 x 10/100 Ethernet MAC
    • AD & DA converters: 3 x AD (12-bit); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
  2. IC42S16400J / IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
  3. MIC2075: onboard USB power management device
  4. AMS1117-3.3: 3.3V voltage regulator
  5. 8M crystal
  6. 32.768K crystal, for internal RTC with calibration
  7. Reset button
  8. VBUS LED
  9. Power indicator
  10. Power supply switch, powered from 5Vin or USB connection
  11. Boot mode selection, for configuring BOOT0 pin
  12. JTAG/SWD interface: for debugging/programming
  13. USB connector, supports Device and/or Host
  14. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
  15. Power jumper
    • VBAT: short the jumper to use system power supply, open it to connect external power, such as battery
    • VREF: short the jumper to connect VREF+ to VCC, open it to connect VREF+ to other custom pin via jumper wire
  16. OTG jumper
    • short the jumper when using USB OTG/HOST
    • open the jumper to disconnect from related I/O port

Note: Core746I provides JTAG/SWD debugging interface, yet does NOT integrate any debugging function, a debugger is required.

JTAG/SWD interfaces

The figure 1, and 2 show the header pinouts of JTAG/SWD interface

Figure 1. JTAG Header Pinout
JTAG Header Pinout
Figure 2. SWD Header Pinout
SWD Header Pinout

Development Resources

  • Schematic
  • Demo code (examples in C, FreeRTOS, μC/OS-III)
  • STM32 development software (KEIL, STM32CubeMX, etc.)
  • STM32 datasheets
  • STM32 development documentations

Wiki: www.waveshare.com/wiki/Core746I

Dimensions

STM32 MCU core board dimensions

Weight: 0.095 kg

Quick Overview

  1. Core746I x 1
  2. USB type A plug to micro B plug cable x 1
1
2

Related Products